AW4 Breather Tube to Case Fitting
#1
Member
Thread Starter
Join Date: Jul 2015
Location: Fort Worth, TX
Posts: 206
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0
AW4 Breather Tube to Case Fitting
See image for reference... my fitting broke when pulling the transmission. This part is no longer made and I can't seem to locate one or find some kind of fitting that would work. Any ideas?
#2
Newbie
Join Date: Dec 2018
Location: Whittier Ca
Posts: 9
Likes: 0
Received 1 Like
on
1 Post
Model: Cherokee (XJ)
Engine: 4.0
Transmission vent
Hey bud I am in the same boat. Did you every figure out an alternative for this piece? Maybe a press fit brass one like the one in the transfer case with some rtv??
#3
Senior Member
Join Date: Mar 2016
Location: Oklahoma
Posts: 621
Likes: 0
Received 9 Likes
on
9 Posts
Year: 1992
Model: Cherokee
Engine: 4.0L L6 PowerTech (stock)
Have you checked the generic dorman products at your local parts store? You might also be able to use a rubber tube instead of a plastic elbow.
#4
Member
Thread Starter
Join Date: Jul 2015
Location: Fort Worth, TX
Posts: 206
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0
I sold this jeep about two years ago so I’m hardly on here; but, this was the most infuriating thing I dealt with through the whole trans rebuild. No one had this part. I bought TONS of vac fittings to see if they’d work. You can’t thread the hole because the area is too small to work with. What I ended up doing is “gluing” the nub that was left of mine back in with RTV. Held up fine and served its purpose.
#6
Newbie
Join Date: Dec 2018
Location: Whittier Ca
Posts: 9
Likes: 0
Received 1 Like
on
1 Post
Model: Cherokee (XJ)
Engine: 4.0
Thank you everyone for all the help! Let's hope I didn't toss it or else I will run to the parts store and macgyver something that will work.
I wonder if anyone has thought about 3d printing them, you'd save lives and many curse words at inanimate objects.
Worst case I just won't go swimming and water log the freshly rebuilt trans
I wonder if anyone has thought about 3d printing them, you'd save lives and many curse words at inanimate objects.
Worst case I just won't go swimming and water log the freshly rebuilt trans
#7
CF Veteran
Join Date: Oct 2018
Location: United Kingdom
Posts: 1,576
Received 278 Likes
on
242 Posts
Year: 1995 RHD
Model: Cherokee (XJ)
Engine: 4.0l
Thank you everyone for all the help! Let's hope I didn't toss it or else I will run to the parts store and macgyver something that will work.
I wonder if anyone has thought about 3d printing them, you'd save lives and many curse words at inanimate objects.
Worst case I just won't go swimming and water log the freshly rebuilt trans
I wonder if anyone has thought about 3d printing them, you'd save lives and many curse words at inanimate objects.
Worst case I just won't go swimming and water log the freshly rebuilt trans
Trending Topics
#8
Old fart with a wrench
From the picture it looks like it just holds a hose and snaps into the trans.
Thread
Thread Starter
Forum
Replies
Last Post
Bwallace33908
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
6
05-23-2013 04:19 PM
OconeeCherokee
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
3
03-23-2011 12:41 AM
Dogberri
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
7
10-01-2010 11:18 AM
Starbuck75
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
4
01-12-2009 07:51 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)