Jeep Cherokee Forum
0 2023/08/12 19:22:15
0 2023/08/11 13:44:27
0 2023/08/11 13:44:24
0 2023/08/11 13:44:19
0 2023/08/11 13:35:12
0 2023/08/11 13:35:04
0 2023/08/11 13:34:57
0 2023/08/11 13:31:27
0 2023/08/11 06:33:31
0 2023/08/11 06:33:24
0 2023/08/11 06:33:18
I even removed and replaced the painters tape with it.
I even removed and replaced the painters tape with it.
0 2023/08/10 16:03:49
0 2023/08/10 16:03:43
I went all around to create a good strong seal. This is supposed to be heat deflective and water resistant. Which is good because i bet theres quite a bit of heat that comes from the trans tunnel, and the moisture content in climate controlled air. It was the perfect idea.
I went all around to create a good strong seal. This is supposed to be heat deflective and water resistant. Which is good because i bet theres quite a bit of heat that comes from the trans tunnel, and the moisture content in climate controlled air. It was the perfect idea.
0 2023/08/10 16:03:35
I tried to rivet the parts together but they kept pulling out because the plastic is so thin. Then i taped the two parts together with HVAC tape. (I like to call it aircraft tape)
I tried to rivet the parts together but they kept pulling out because the plastic is so thin. Then i taped the two parts together with HVAC tape. (I like to call it aircraft tape)
0 2023/08/10 16:03:29
I also did the air supply hole.
I also did the air supply hole.
0 2023/08/10 15:57:37
I removed the lower vent assembly (not sure what the Chrystler name is) and applied new foam to where its going into the vent relocation.
I removed the lower vent assembly (not sure what the Chrystler name is) and applied new foam to where its going into the vent relocation.
0 2023/08/10 15:57:30
I indexed the parts so I how they should line up.
I indexed the parts so I how they should line up.
0 2023/08/10 15:57:24
You can see here why I am mounting it upside down. I want the air to travel upwards to the vent.
You can see here why I am mounting it upside down. I want the air to travel upwards to the vent.
0 2023/08/10 15:57:16
I cut the rear air feed tube from the interface. The angle is sloping downward though. Sorry I didnt take pictures, but I remarked the hole and cut it upside down because of the angle.
I cut the rear air feed tube from the interface. The angle is sloping downward though. Sorry I didnt take pictures, but I remarked the hole and cut it upside down because of the angle.
0 2023/08/10 15:57:09
This is how it sits from the factory with the tube down the passenger side.
This is how it sits from the factory with the tube down the passenger side.
0 2023/08/10 15:57:02
Marked out the opening through the vent adapter
Marked out the opening through the vent adapter
0 2023/08/10 15:56:53
0 2023/08/09 18:33:49
0 2023/08/09 18:33:42
0 2023/08/09 18:33:33
0 2023/08/08 19:03:05
Go the bondo sanded down to clean lines
Go the bondo sanded down to clean lines
0 2023/08/08 19:02:58
Sanded the whole thing down to 180 grit. I was going to do textured paint but figured I wouldnt be happy with it. I think the texture would be too large and it would remind me more of bedliner rather than what was originally on there. So I opted out for a smooth look.
Sanded the whole thing down to 180 grit. I was going to do textured paint but figured I wouldnt be happy with it. I think the texture would be too large and it would remind me more of bedliner rather than what was originally on there. So I opted out for a smooth look.
0 2023/08/08 19:02:50
Progress so far 😁😁😁
Progress so far 😁😁😁
0 2023/08/06 12:03:53
0 2023/08/06 11:52:01
Im going to lay the vent on top of the cubby and then lay the console insert over the whole thing.
Im going to lay the vent on top of the cubby and then lay the console insert over the whole thing.
0 2023/08/06 11:51:53
You can start to see here how I will intrigrate it with the air supply.
You can start to see here how I will intrigrate it with the air supply.
0 2023/08/06 11:49:04
0 2023/08/06 11:48:57
0 2023/08/06 11:48:50
I cut a hole in the front of the change cubby
I cut a hole in the front of the change cubby
0 2023/08/06 11:48:43
And angled the corners so it would sit inside of the walls
And angled the corners so it would sit inside of the walls
0 2023/08/06 11:43:49
I trimmed all of the excess plastic around the vent so it would sit flush
I trimmed all of the excess plastic around the vent so it would sit flush
0 2023/08/06 11:43:41
I shaved off the lip that interfaces with the rest of the black center console insert.
I shaved off the lip that interfaces with the rest of the black center console insert.
0 2023/08/06 11:40:12
And broke off the change cubby that sits under the ashtray.
And broke off the change cubby that sits under the ashtray.
0 2023/08/06 11:40:05
I removed the vent from under the climate controls on a spare dash that I had.
I removed the vent from under the climate controls on a spare dash that I had.
0 2023/08/06 11:39:59