oh. thats still not terribly hard to do an axle swap on.

 

all fuses under dash and hood are good, took apart headlight switxh, it's reading in the tolerances, took apart turn signal selecter lever on coloumn it's good, I'm freakin stumped, wish I could find a dedicated diagram to all the ground points...

 

I totally read that wrong. Check the relay first. I read it as your dash lights weren't coming on but everything else was. Maybe I shouldn't reply to stuff on here when I've been awake for 26 hours

Swap it out with a known good one, I wouldn't be surprised if all of the sudden your headlights worked perfectly

If that doesn't do it check all your grounds, if you have no joy then I'd say swap the headlight switch for a known good one.

Normally I don't recommend throwing parts at a vehicle but when they're as cheap as a relay or a JY headlight switch, why not. Plus with those two parts having a spare around is a good idea

 

my rear lights are not working they only work when i put the brake on and my turn signals only stay on and not blink and my dash lights are out too. how can i fix this problem. --------- jeep'n johnny

 

In a jeep this means you have a blown bulb. Turn on your emergency flashers and see which one doesn't light up - that's the bad one. Flashing should resume once the bulb is replaced.

Note that it could be the front bulb that's burnt out - the flashing circuit is connected between the front and rear.

 

will that make the rear brake lights to go out to?
and do u think its a fuse for the dash?

 

You said the brake lights work? (note: brake lights are the portion that comes on when you step on the brakes, turn signals are a different bulb).

most likely

 

yah they come on when i am on the brake but if my foot is not on the brake they r off.

 

anybody know of a good ground diagram for a 90 mj (xj is the same one)

 

this should give you the info you seek.

http://www.greatlakesxj.com/tech/90fsm.pdf

 

I already posted a thread but I will post ask you guys on here too. I have a 94 Grand Cherokee with the 4.0. The trani wouldn't shift into overdrive one day last August and would just get high RPM's as I went faster on the interstate. I tried to keep it under 3 grand on my way home but when I got to town it started slipping real bad in second. So, it took a long time but a buddy and I rebuilt the trani. The intermediate shaft and a plate had sheared.
We got it finished up last night, put new shaft and plate, new torque converter, filter, gaskets, ect... Put fluid in it tonight and started it up and it was shifting a little rough but not far from normal. I disconnected one of the hoses to check and see if the fluid was being pumped sufficiently and it poured out, so that is good. When we went for a drive in it, the shifting was pretty good but it wouldn't shift into overdrive, just like before. I don't know if it is the transmission control module or some sensor telling it not to. I do know that I don't want to take that trani apart again. That overdrive was a major pain.
Anyway, if anyone has any ideas, that'd be great.

 

Hey there folks.

So I think i may have found the leak issue and I need a little help to get the ider pulley on the front of the water pump off. I see that it must come off but as I try to remove the bolts on it the pulley spins. UGH SO frustrating as I am afraid I will bend it. Any help would be great.

Thanks
Jon

 

Does anyone have pictures from a 6.5 inch speaker install in the doors and/or sound bar they can post or email to me? Bhsmith.FL@Gmail.com

I'm sure once I get started it will be easy but it would be nice to see some pictures first. I know I've seen some around here somewhere but I couldn't find them. Thank. You!

 

Ok you need to check the fuses under the dash.

Fuse 7 (10amp) is for parking lights and dash illumination dimmer
Fuse 9 (5amp) is for instrument panel illumination
Fuse 4 (20amp) is for turn signals

i would check all of them though - it's possible yours is different (those numbers came from a 1988 FSM)

Afterwards, check the bulbs like i said above

 

In my soundbar, haven't gotten to the doors yet
http://www.jeepforum.com/forum/f11/r...heavy-1104865/




Here are some more links w/ pictures from my research:
http://www.lunghd.com/Tech_Articles/...l/Speakers.htm
http://junkyardjeep.blogspot.com/200...-speakers.html