Hack and Tap VS Other SYE kits
#1
Seasoned Member
Thread Starter
Join Date: Feb 2010
Location: Co
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: I6
Hack and Tap VS Other SYE kits
I got bad vibs and i know i need something with my 4.5 inch lift. SO i don't know what is better what is the advantages and disadvantages and types of Slip Yoke eliminators. Thanks for the help i need it.
#2
I ran an RE H&T SYE with a front Drive shaft and a Spicer 211229x flange adapter for years. The only problem I had with it was a lost lock ring. I ended up welding the washer into the adapter .
Installing it was a challenge. My first attempt resulted in a hole in the shaft that wasn't nerfectly centered. I replaced the shaft and put the entire t-case on my drillpress table for the second attempt at drilling the shaft...worked beautifully.
After installing my new motor I had to swithch to a short shaft SYE from JB Conversions. Great product but a little pricey. ya get what ya pay for though....and it was the only thing that work for my application.
Any difference between the two as far as driveability is concerned? No, none at all.
Either style will work just fine.
Installing it was a challenge. My first attempt resulted in a hole in the shaft that wasn't nerfectly centered. I replaced the shaft and put the entire t-case on my drillpress table for the second attempt at drilling the shaft...worked beautifully.
After installing my new motor I had to swithch to a short shaft SYE from JB Conversions. Great product but a little pricey. ya get what ya pay for though....and it was the only thing that work for my application.
Any difference between the two as far as driveability is concerned? No, none at all.
Either style will work just fine.
#3
CF Veteran
Join Date: Nov 2008
Location: Stokesdale, NC
Posts: 1,350
Likes: 0
Received 5 Likes
on
4 Posts
Year: 89XJ,98ZJ,72K10, 06 Tundra..
Model: Cherokee
Engine: 4.0
RE H&T
I run an RE hack and tap. Got 50K on it, along with a custom shaft, Tom Woods I believe. Never a problem, been to Wharton, Uwharrie, NY, MA, Tellico... never a problem.
Rolled under the jeep, cut off a bit, punched a center hole, drilled, tapped, bolted it on...been perfect ever since.
Im at 4.5 on an 89 with 231TC.
Rolled under the jeep, cut off a bit, punched a center hole, drilled, tapped, bolted it on...been perfect ever since.
Im at 4.5 on an 89 with 231TC.
#5
Senior Member
Join Date: Oct 2009
Location: Southern Utah
Posts: 532
Likes: 0
Received 1 Like
on
1 Post
Year: 1992
Model: Cherokee
Engine: 4.0 I6
Sorry for the highjack, but lets say, i got an Iron rock offroad Hack and Tap and i didnt cut off that much spline, maybe an inch (per their instructions)
and it leaks like crazy. how much spline have you all cut off? im wondering if i cut another inch off if my driveshaft will work. Its just a rebuilt front DC
I didnt get my hole perfectly centered, but my vibes are gone, it just leaks
and it leaks like crazy. how much spline have you all cut off? im wondering if i cut another inch off if my driveshaft will work. Its just a rebuilt front DC
I didnt get my hole perfectly centered, but my vibes are gone, it just leaks
#6
Seasoned Member
Thread Starter
Join Date: Feb 2010
Location: Co
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: I6
My jeep is a 93. I hear a sound when I'm going down the road like there are subs going off and when I get a violent shakes around twenty haven't pushed it past 35. So I assume I got to get the SYE? Also I got some bad bump stear is that normal for a 4.5 inch lift
#7
Junior Member
Join Date: May 2011
Location: columbiana, alabama
Posts: 95
Likes: 0
Received 1 Like
on
1 Post
Year: 1995 xj sport
Model: Cherokee
Engine: 4.0 ho
i got a 95 with a ax15 with the np231 t case lookin to put a sye on or go with a hach-n -tap my xj has around 8 in of lift no trimming and a tc drop of about 2 of tc drop would this work for me using the hackntap?
Trending Topics
#8
CF Veteran
Join Date: Mar 2010
Location: Broward County Fl.
Posts: 47,923
Likes: 0
Received 22 Likes
on
22 Posts
Year: 1989 xj sport 2dr
Model: Cherokee
Engine: 12 hole bosch Injectors
Sorry for the highjack, but lets say, i got an Iron rock offroad Hack and Tap and i didnt cut off that much spline, maybe an inch (per their instructions)
and it leaks like crazy. how much spline have you all cut off? im wondering if i cut another inch off if my driveshaft will work. Its just a rebuilt front DC
I didnt get my hole perfectly centered, but my vibes are gone, it just leaks
and it leaks like crazy. how much spline have you all cut off? im wondering if i cut another inch off if my driveshaft will work. Its just a rebuilt front DC
I didnt get my hole perfectly centered, but my vibes are gone, it just leaks
#9
Seasoned Member
I have an 89' Cherokee with NP242. I installed a SYE kit from Mechanically Inclined Technicians: http://www.mit4x4.com/ myself in 2003 along with a telescoping drive shaft. I am fortunate to have access to a lift in the Auto Hobby Shop on base. Five bucks an hour. I have had no problems or complaints with the operation and performance. The install was a bit of a challenge with the C-clips inside the transfer case though. It would be nice if there were holes in the ends of the C-clips so snap ring pliers would work. I think this conversion is a must with 3" and higher lifts.
#10
Seasoned Member
Join Date: Aug 2009
Location: Long Island NY
Posts: 460
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
Sorry for the highjack, but lets say, i got an Iron rock offroad Hack and Tap and i didnt cut off that much spline, maybe an inch (per their instructions)
and it leaks like crazy. how much spline have you all cut off? im wondering if i cut another inch off if my driveshaft will work. Its just a rebuilt front DC
I didnt get my hole perfectly centered, but my vibes are gone, it just leaks
and it leaks like crazy. how much spline have you all cut off? im wondering if i cut another inch off if my driveshaft will work. Its just a rebuilt front DC
I didnt get my hole perfectly centered, but my vibes are gone, it just leaks
hope this helps you
Last edited by TheGreatGazoo; 06-12-2011 at 09:48 PM.
Thread
Thread Starter
Forum
Replies
Last Post
RickJames Bish
Modified XJ Cherokee Tech
5
09-02-2015 03:22 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)