My replacement 95 xj
#181
Member
Join Date: Aug 2010
Location: michigan
Posts: 111
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 I6
Don't be fooled. It's not so "cheap" in the end as u will find out Heims along with high misalignment spacers and hardware all add up. Though it will be cheaper then some kits probably. Tie rod ends are also a bit expensive But good luck and let me know if you have questions
#182
CF Veteran
Thread Starter
Join Date: May 2011
Location: Aurora, Co
Posts: 2,320
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 HO
So I don't know why I didn't do 7/8 Heims. I'm kinda wishing I had now but 3/4 will probably be ok. And the bracket came from ballistic fabrication and its awesome. Easy to weld together and pretty beefy. I need to rebuild my "frame" end mount because the one I built hits the coil.
#183
Member
Join Date: Aug 2010
Location: michigan
Posts: 111
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 I6
So I don't know why I didn't do 7/8 Heims. I'm kinda wishing I had now but 3/4 will probably be ok. And the bracket came from ballistic fabrication and its awesome. Easy to weld together and pretty beefy. I need to rebuild my "frame" end mount because the one I built hits the coil.
#184
CF Veteran
Thread Starter
Join Date: May 2011
Location: Aurora, Co
Posts: 2,320
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 HO
Yea after I wrote you I found that bracket. I'm going to get the steering kit from ballistic with 7/8 heims. Then I was just looking at the tnt trac bar kit. Comes with axle bracket and "frame" side. Seems the easiest way to go. I'm running 15x8 wheels with 3.75 backspacing. Do you think I will run into any clearance issues with 7/8 heims? Your xj is where I'm getting all my ideas from man. Its badass!
#185
Senior Member
Join Date: Mar 2012
Location: ROCKFORD IL
Posts: 943
Likes: 0
Received 1 Like
on
1 Post
Year: 1998, 1993
Model: Cherokee
Engine: 4.0
nice build. I like your rear bumper. Once I get a welder I want to add cut and fold supports and build a tire carrier. I also like the supports you welded to your hitch.
my plan to stick with is a final 4.5" on 33x10.50s havent decided on gears yet
my plan to stick with is a final 4.5" on 33x10.50s havent decided on gears yet
#186
CF Veteran
Thread Starter
Join Date: May 2011
Location: Aurora, Co
Posts: 2,320
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 HO
Thanks man I also have a thread on my bumper in the fab section. Sounds like a good plan. You should do 4:56 I'm still on 4:10 and 35s and its not too horrible but mileage is bad
#188
CF Veteran
Thread Starter
Join Date: May 2011
Location: Aurora, Co
Posts: 2,320
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 HO
#190
Junior Member
Join Date: Aug 2012
Location: Westminster, CO
Posts: 82
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0L I6
Nice build man! Glad to see another flat black colorado xj. Our rigs look similar. We should wheel sometime! Keep up the good work!
Thread
Thread Starter
Forum
Replies
Last Post
Blackcherokee290
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
27
07-26-2022 07:52 PM
Jose Calderon
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
17
09-17-2015 08:57 PM
Zeke P. Lucas
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
8
08-30-2015 05:42 PM
David Chauncey Clothier
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
2
08-29-2015 09:31 PM
Zerocyde
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
5
08-24-2015 10:56 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)