Tidewater/Hampton Cherokees????
Senior Member
Joined: Dec 2010
Posts: 903
Likes: 1
From: Linthicum, Md
Year: 1987
Model: Cherokee
Engine: 1987 4.0L (242 CID) I6 RENIX FI 242 173 hp (129 kW) @ 4600 rpm, 224 lb•ft (304 N-m) @ 4000RPM
Newbie
Joined: Jan 2013
Posts: 20
Likes: 0
From: Virginia Beach
Year: 2001
Model: Cherokee
Engine: 4.0L
It's been at least 5 years. I got more than a few 'no front tag' tickets, but I know there was a bill introduced recently to remove the front tag from being a requirement but not sure if that went through or not. I've got a front tag currently so I haven't paid much attention to it.
I've been going crazy trying to figure out my misfire, if anybody has any ideas here is the link to the thread https://www.cherokeeforum.com/f2/int...1/#post2748644
Senior Member
Joined: Dec 2008
Posts: 584
Likes: 2
From: Gloucester Virginia
Year: 2001
Model: Cherokee
Engine: 4.0 I6
Fuel pressure is out of spec, at idle it ranged from 55 all the way down to 35 at some points. Thinking this is a fuel delivery issue that is causing the misfire.
yeah, I would say so. Start simple and so one thing at a time. Pull the fuel rail and injectors and do a really good clean job on them. Test your pressure again. if it's still bad, check your pump/filter. Test again.
Senior Member
Joined: Dec 2008
Posts: 584
Likes: 2
From: Gloucester Virginia
Year: 2001
Model: Cherokee
Engine: 4.0 I6
I've already pulled injectors and cleaned them up, that's how I know it wasn't an Injector bad.
At this point if I even suspect the pump I'm gona replace it. Found a bosch replacement module for 120 on ebay.
Hope everybody had a safe snow storm, I spent about 5 hours last night on the roads
At this point if I even suspect the pump I'm gona replace it. Found a bosch replacement module for 120 on ebay.
Hope everybody had a safe snow storm, I spent about 5 hours last night on the roads
CF Veteran
Joined: Oct 2011
Posts: 1,812
Likes: 0
From: South Mills, NC
Year: 1998
Model: Cherokee
Engine: Rebuilt 4.0L I6
Went to Pick-n-Pull with a friend today. Got ZJ seats, front skid plate, new driver mirror and some interior parts. Friend got stuff for his MJ, a hood, header panel, 2 grills and roof rack. I tried to get the gas tank skid plate off but the nut strips were broke and I was pissed. Spent 3 hours trying to get an np231 out, we dropped the transmission and transfer case but we couldn't disconnect them from each other.
Junior Member
Joined: Sep 2013
Posts: 96
Likes: 0
From: Fort Eustis Virginia
Year: 1997
Model: Cherokee
Engine: l6
Went to Pick-n-Pull with a friend today. Got ZJ seats, front skid plate, new driver mirror and some interior parts. Friend got stuff for his MJ, a hood, header panel, 2 grills and roof rack. I tried to get the gas tank skid plate off but the nut strips were broke and I was pissed. Spent 3 hours trying to get an np231 out, we dropped the transmission and transfer case but we couldn't disconnect them from each other.
I need to do the same, I don't know where to go though.
Junior Member
Joined: Sep 2013
Posts: 96
Likes: 0
From: Fort Eustis Virginia
Year: 1997
Model: Cherokee
Engine: l6
I loved the look of my rolled fenders but I got sick of things hitting me when the window was down, so I got some bushwacker flares and they are awesome.
Welcome to the forum! Since you're in Suffolk, you're gonna be close to Starr Motors. They have a good club you can join if you're not part of one yet. Joe Bonney is one of t he head organizers if not THE head guy and he's a good guy to talk to about repairs, parts, and mods. Definitely knows his stuff. Here's a link to their club page.
http://www.meetup.com/starr4wdc/
http://www.meetup.com/starr4wdc/



