Jeep Cherokee Forum
0 2020/12/10 14:20:21
0 2020/12/10 14:19:46
Primed and a coat of red to somewhat match.
Primed and a coat of red to somewhat match.
0 2020/12/10 14:18:42
Looks decent tho. Will finish installing next time around and smooth out the body filler
Looks decent tho. Will finish installing next time around and smooth out the body filler
0 2020/10/01 15:30:08
Will have to try and match these curves
Will have to try and match these curves
0 2020/10/01 15:29:58
Inside view
Inside view
0 2020/10/01 15:29:49
0 2020/10/01 15:29:19
0 2020/10/01 15:28:38
0 2020/10/01 15:28:27
0 2020/10/01 15:28:16
0 2020/10/01 15:27:36
Inside
Inside
0 2020/10/01 15:27:00
More Dyna-glass to fill it.
More Dyna-glass to fill it.
0 2020/10/01 15:25:59
To save cutting out more I build up some weld in the thin areas and ground down.
To save cutting out more I build up some weld in the thin areas and ground down.
0 2020/10/01 15:25:06
Mostly installed. Dealing with some super thin .020 metal is tricky.
Mostly installed. Dealing with some super thin .020 metal is tricky.
0 2020/10/01 15:23:45
Fabricated a new inner panel. Wish you could buy these.
Fabricated a new inner panel. Wish you could buy these.
0 2020/10/01 15:22:17
Welded the nuts so they'd be easier to take off if need be
Welded the nuts so they'd be easier to take off if need be
0 2020/10/01 15:20:37
Drilled the top inside and welded on bosses onto the frame to bolt them on with M12 hardware.
Drilled the top inside and welded on bosses onto the frame to bolt them on with M12 hardware.
0 2020/10/01 15:19:04
0 2020/10/01 15:18:29
Installed Ironman Fab no lift relocation boxes but modified them so that they didn't put holes in the floor.
Installed Ironman Fab no lift relocation boxes but modified them so that they didn't put holes in the floor.
0 2020/10/01 15:15:47
Cut out the rusted lower quarter on the right side. Thankfully the left side is ok.
Cut out the rusted lower quarter on the right side. Thankfully the left side is ok.
0 2020/10/01 15:14:38
Finished filling all the irregularities from the frame stiffeners
Finished filling all the irregularities from the frame stiffeners
0 2020/10/01 15:13:47
Some body filler to smooth out the floors
Some body filler to smooth out the floors
0 2020/10/01 15:12:39
So damn cool that it said that from the factory
So damn cool that it said that from the factory
0 2020/10/01 15:11:04
Sat in a field with a seized engine for 15 years
Sat in a field with a seized engine for 15 years
0 2020/10/01 15:10:07
0 2020/10/01 15:08:55
One of the deleted drains after filler.
One of the deleted drains after filler.
0 2020/05/10 21:00:01
Filling the welds on the bottom side so that when it's painted it'll be hard to even tell it has frame stiffeners.
Filling the welds on the bottom side so that when it's painted it'll be hard to even tell it has frame stiffeners.
0 2020/05/10 20:57:09
0 2020/05/10 20:56:14
Sanded.
Sanded.
0 2020/05/10 20:54:18
0 2020/05/10 20:53:11
Dyna-glass
Dyna-glass
0 2020/05/10 20:52:11
So this is my issue with the IRO center stiffener. The top edge extends past the "frame" rolled piece and would need to be welded to the floor pan. Now we all know how thick and sturdy XJ floors pans are... Just wasn't going to be possible seeing the pan I'm working with is roughly .060" thick.
So this is my issue with the IRO center stiffener. The top edge extends past the "frame" rolled piece and would need to be welded to the floor pan. Now we all know how thick and sturdy XJ floors pans are... Just wasn't going to be possible seeing the pan I'm working with is roughly .060" thick.
0 2020/05/10 20:47:16
This is how they ended up going on. The pan would of ended up failing at the weld and it would of been impossible to get it right. Cut back and welded to the "frame" is the way to go if you buy these.
This is how they ended up going on. The pan would of ended up failing at the weld and it would of been impossible to get it right. Cut back and welded to the "frame" is the way to go if you buy these.
0 2020/05/10 20:38:29
The passenger side E-brake cable mount in the tunnel had a small tear near the spot weld so I welded on a plate to stiffen it up
The passenger side E-brake cable mount in the tunnel had a small tear near the spot weld so I welded on a plate to stiffen it up
0 2020/05/10 20:31:01
The largest piece of floor repair. Minor pitting in the buffed areas which will be filled with short strand fibreglass body filler.
The largest piece of floor repair. Minor pitting in the buffed areas which will be filled with short strand fibreglass body filler.
0 2020/05/10 20:29:03
Seeing as I don't plan on forging any rivers in this Jeep I ended up welding shit all of the floor drain plugs. I was going to leave a couple but if it ever gets that wet inside I'll promptly pull the interior and dry it out properly. Also don't know why Jeep thought it needed so many of them, took some serious time.
Seeing as I don't plan on forging any rivers in this Jeep I ended up welding shit all of the floor drain plugs. I was going to leave a couple but if it ever gets that wet inside I'll promptly pull the interior and dry it out properly. Also don't know why Jeep thought it needed so many of them, took some serious time.
0 2020/05/10 20:25:33
0 2020/03/31 12:42:47
0 2020/03/31 12:42:08
I'll post some finished pics when I grind it all.
I'll post some finished pics when I grind it all.
0 2020/03/31 12:41:21