Jeep Cherokee Forum
0 2022/04/14 16:35:06
Picked up a sound bar for mine as it didn't have the be, not sure if it was available in 91. Getting the same 6.5" NVX coaxials. Some trimming and modification to the speaker frame to get the factory grills to fit but it turned out ok.
Picked up a sound bar for mine as it didn't have the be, not sure if it was available in 91. Getting the same 6.5" NVX coaxials. Some trimming and modification to the speaker frame to get the factory grills to fit but it turned out ok.
0 2022/04/14 16:33:13
0 2022/04/14 16:27:33
0 2022/04/14 16:27:18
0 2022/04/14 16:27:00
0 2022/04/14 16:26:45
I'm adding a sound bar to mine, not sure if it was available in a 91. Put the same 6.5" NVX coaxials in it with some trimming and modification to the speaker frame to accept the factory cover. I couldn't roll it enough without distorting to fit over the outside of the speaker so it just sits inside a raised lip on the frame.
I'm adding a sound bar to mine, not sure if it was available in a 91. Put the same 6.5" NVX coaxials in it with some trimming and modification to the speaker frame to accept the factory cover. I couldn't roll it enough without distorting to fit over the outside of the speaker so it just sits inside a raised lip on the frame.
0 2022/04/14 16:23:50
Door panel back on and still looks factory.
Door panel back on and still looks factory.
0 2022/04/13 04:02:03
0 2022/04/13 04:01:42
Sound deadened the door on the outer skin, covered the holes and resealed the door.
Sound deadened the door on the outer skin, covered the holes and resealed the door.
0 2022/04/13 03:59:01
NVX speaker baffles and acoustic pad
NVX speaker baffles and acoustic pad
0 2022/04/13 03:56:50
Installed rivet nuts to mount the speaker, filled the gaps with Devcon and painted.
Installed rivet nuts to mount the speaker, filled the gaps with Devcon and painted.
0 2022/04/13 03:55:34
0 2022/04/13 03:54:46
Cut some new mount rings out of sheet metal
Cut some new mount rings out of sheet metal
0 2022/04/13 03:54:02
0 2022/04/13 03:53:28
0 2022/04/13 03:52:41
I didn't take a before picture but the factory 5.25" speaker was recessed about .5" and some fabrication was needed to fit the 6.5" speakers I got for it. Had to cut the hole bigger and recess the speaker about .75" so that the door panel could still go on without being cut up.
I didn't take a before picture but the factory 5.25" speaker was recessed about .5" and some fabrication was needed to fit the 6.5" speakers I got for it. Had to cut the hole bigger and recess the speaker about .75" so that the door panel could still go on without being cut up.
0 2022/04/13 03:43:03
0 2022/04/12 19:28:14
Finished sound treatment on the floor.
Finished sound treatment on the floor.
0 2022/04/12 19:27:43
Mounted the T case and am hoping it seals as I have the short input on this one so I had to run the trans output seal out further than I would of liked. Fingers crossed.
Mounted the T case and am hoping it seals as I have the short input on this one so I had to run the trans output seal out further than I would of liked. Fingers crossed.
0 2022/03/17 15:41:10
0 2022/03/17 15:36:49
Started sound deadening
Started sound deadening
0 2022/03/17 15:36:11
0 2022/03/17 15:34:28
0 2022/03/17 15:32:56
Painted
Painted
0 2022/03/17 15:32:36
Reassembled and cleaned
Reassembled and cleaned
0 2022/03/17 15:32:10
0 2022/01/29 15:29:27
0 2022/01/29 15:28:47
Chain didn't look stretched and the gears were in fair shape so I'm not gonna change them.
Chain didn't look stretched and the gears were in fair shape so I'm not gonna change them.
0 2022/01/29 15:27:48
Started going through the transfer case I'm going to use. It's a NP242 short stick out from a 94 XJ. It was caked in dirt so I'm gonna assume every seal is leaking.
Started going through the transfer case I'm going to use. It's a NP242 short stick out from a 94 XJ. It was caked in dirt so I'm gonna assume every seal is leaking.
0 2022/01/29 15:26:09
Wired in a converter for the trailer lights
Wired in a converter for the trailer lights
0 2022/01/29 15:25:30
Cleaned and installed the splash guards and installed rivet nuts so that I can bolt them on rather than weak push clips. Also started it for the first time. I had some trouble getting it going due to a leak in the fuel regulator and then the distributor being indexed just a bit out but got that all sorted out.
Cleaned and installed the splash guards and installed rivet nuts so that I can bolt them on rather than weak push clips. Also started it for the first time. I had some trouble getting it going due to a leak in the fuel regulator and then the distributor being indexed just a bit out but got that all sorted out.
0 2022/01/22 15:20:15
Powder coating everything now. Wish I had bought it earlier
Powder coating everything now. Wish I had bought it earlier
0 2022/01/22 15:19:15
0 2022/01/22 15:18:55
Fenders and grill on. Added some LED headlights.
Fenders and grill on. Added some LED headlights.
0 2022/01/22 15:17:55
Powder coated transmission Mount plate
Powder coated transmission Mount plate
0 2022/01/22 15:16:45
Got setup for powder coating, using an Eastwood gun.
Got setup for powder coating, using an Eastwood gun.
0 2022/01/22 15:15:47
New set of Crown fender flare brackets
New set of Crown fender flare brackets
0 2022/01/22 15:14:02
0 2022/01/22 15:13:18
0 2022/01/22 15:13:01