Jeep Cherokee Forum
French drive shaft rebuilt and installed. Picked up an iron Rock off-road hack and tap for the 242 transfer case will need to find another front drive shaft for back there.
French drive shaft rebuilt and installed. Picked up an iron Rock off-road hack and tap for the 242 transfer case will need to find another front drive shaft for back there.
0 2023/03/05 19:35:02
3D printed a mount for the receiver and basically just put it up underneath the dash near the steering column
3D printed a mount for the receiver and basically just put it up underneath the dash near the steering column
0 2023/03/05 19:34:56
0 2023/03/05 19:34:51
0 2023/03/05 19:34:45
Wired in a NVX Bluetooth receiver. Wasn't too hard once I found the information, basically just send the input into it and then remove a resistor. You give up AM but nobody listens to that anyways. Sound quality is okay however I am a bit picky when it comes to sound quality, so we'll see how I fare with it. Nice to be able to adjust your volume with the factory look and knob.
Wired in a NVX Bluetooth receiver. Wasn't too hard once I found the information, basically just send the input into it and then remove a resistor. You give up AM but nobody listens to that anyways. Sound quality is okay however I am a bit picky when it comes to sound quality, so we'll see how I fare with it. Nice to be able to adjust your volume with the factory look and knob.
0 2023/03/05 19:34:40
New shifter boot
New shifter boot
0 2023/03/05 19:32:42
0 2023/03/05 19:31:31
0 2023/03/05 19:30:40
0 2023/03/05 19:29:21
Headliner and panels back in as well as protection film on the carpet. I've got two big dogs and am done with the hair being stuck in it all the time.
Headliner and panels back in as well as protection film on the carpet. I've got two big dogs and am done with the hair being stuck in it all the time.
0 2023/03/05 19:27:46
Front driveshaft rebuilt and installed. Need to get another for the rear. Picked up an IRO Hack and Tap so I'll be doing that this week.
Front driveshaft rebuilt and installed. Need to get another for the rear. Picked up an IRO Hack and Tap so I'll be doing that this week.
0 2023/03/05 19:26:27
New shifter boot
New shifter boot
0 2023/03/05 19:25:21
0 2023/03/05 19:24:58
0 2023/03/05 19:24:34
Wired a NVX Bluetooth adapter into the factory radio. Wasn't terrible once I had the information needed. Basically just send the input into the board and remove a resistor and you're good to go. Loses AM but nobody uses that anyways. It sounds decent I guess, however I'm a bit picky about sound quality, so we'll see if I'm ok with it not being perfect. It is super nice to keep the factory look and still be able to adjust volume on the knob. I 3D printed a mount for the receiver under the dash
Wired a NVX Bluetooth adapter into the factory radio. Wasn't terrible once I had the information needed. Basically just send the input into the board and remove a resistor and you're good to go. Loses AM but nobody uses that anyways. It sounds decent I guess, however I'm a bit picky about sound quality, so we'll see if I'm ok with it not being perfect. It is super nice to keep the factory look and still be able to adjust volume on the knob. I 3D printed a mount for the receiver under the dash
0 2023/03/05 19:18:32
0 2022/08/03 08:04:12
0 2022/08/03 08:04:02
0 2022/08/03 08:03:15
0 2022/08/03 08:03:00
0 2022/08/03 08:01:39
0 2022/08/03 08:01:14
0 2022/08/03 08:00:58
0 2022/08/03 08:00:39
0 2022/08/03 07:58:58
0 2022/08/03 07:57:49
Powder coated in a wrinkle finish
Powder coated in a wrinkle finish
0 2022/08/03 07:57:12
0 2022/08/03 07:56:47
0 2022/08/03 07:56:06
0 2022/08/03 07:55:37
Made some amp racks for under the rear seat
Made some amp racks for under the rear seat
0 2022/08/03 07:55:16
0 2022/05/11 09:45:27
0 2022/05/11 09:45:14
0 2022/05/11 09:44:39
0 2022/05/11 09:44:25
And big news as I finally found a teal XJ that wasn't rusted out. Naturally the wife and I snagged it.
And big news as I finally found a teal XJ that wasn't rusted out. Naturally the wife and I snagged it.
0 2022/05/11 09:42:45
0 2022/05/11 09:36:33
So after some mock up it was clear the same 6.5" NVX speakers weren't going to fit recessed into the rear hatch as they were too tall. Luckily tho, they did come with a spacer ring to protect the surround and cone. I top mounted them on the hatch and when the rear panel goes back on it will contact the spacer and be ok. The bow in the panel will be hardly noticeable so I'm happy with that.
So after some mock up it was clear the same 6.5" NVX speakers weren't going to fit recessed into the rear hatch as they were too tall. Luckily tho, they did come with a spacer ring to protect the surround and cone. I top mounted them on the hatch and when the rear panel goes back on it will contact the spacer and be ok. The bow in the panel will be hardly noticeable so I'm happy with that.
0 2022/05/11 09:32:27
0 2022/04/14 16:35:56
0 2022/04/14 16:35:38
0 2022/04/14 16:35:22