Jeep Cherokee Forum
Also started sanding down the engine bay for a repaint. Should really look clean in there when it's done. Will likely spray it with a gun as I couldn't find any color matched spray paint. Plus it would be a lot of area to cover with cans.
Also started sanding down the engine bay for a repaint. Should really look clean in there when it's done. Will likely spray it with a gun as I couldn't find any color matched spray paint. Plus it would be a lot of area to cover with cans.
0 2019/10/25 17:09:57
0 2019/10/25 17:09:05
Going to prime and paint the places that the frame stiffeners cover before they get welded on then prime and paint the whole thing. Don't want any bare metal or just primer behind them to rust up.
Going to prime and paint the places that the frame stiffeners cover before they get welded on then prime and paint the whole thing. Don't want any bare metal or just primer behind them to rust up.
0 2019/10/25 17:07:04
0 2019/10/25 17:05:51
0 2019/10/25 17:04:59
0 2019/10/25 17:03:19
0 2019/10/25 17:01:47
Made it about 10 feet out of the alley before I had to go back a toss the shocks back on. Got some wicked wheel hop immediately haha
Made it about 10 feet out of the alley before I had to go back a toss the shocks back on. Got some wicked wheel hop immediately haha
0 2019/10/25 16:53:51
Also welded these on the old leafs so I could throw the axle back under it to push it outside and sandblast the tough to reach areas
Also welded these on the old leafs so I could throw the axle back under it to push it outside and sandblast the tough to reach areas
0 2019/10/11 11:08:13
0 2019/10/11 11:07:44
Not going to completely tear it down but it will get new freeze plugs, block heater, VC and oil pan gaskets, rear main seal etc.
Not going to completely tear it down but it will get new freeze plugs, block heater, VC and oil pan gaskets, rear main seal etc.
0 2019/10/11 11:06:09
0 2019/10/11 11:05:24
0 2019/10/11 11:04:32
Going to reinstall the axle so it's resting on its wheels before I start welding on the stiffeners. Debating whether to mix epoxy primer and spray before they go on or just spray balm it them epoxy primer it all one they're on there.
Going to reinstall the axle so it's resting on its wheels before I start welding on the stiffeners. Debating whether to mix epoxy primer and spray before they go on or just spray balm it them epoxy primer it all one they're on there.
0 2019/10/02 05:02:14
0 2019/10/02 05:01:10
0 2019/10/02 05:00:21
Getting there
Getting there
0 2019/10/02 04:59:32
Had to weld on a nut on one side and work it free
Had to weld on a nut on one side and work it free
0 2019/10/02 04:58:58
0 2019/09/25 11:40:02
0 2019/09/25 11:38:24
0 2019/09/25 11:38:14
0 2019/09/25 11:38:03
0 2019/09/25 11:37:54
0 2019/09/25 11:37:44
0 2019/09/25 11:37:33
0 2019/09/13 21:44:19
After! courtesy of my fantastic girlfriend. Also have some 3.55 geared axles out of a 97, Just waiting to be sandblasted and resealed.
After! courtesy of my fantastic girlfriend. Also have some 3.55 geared axles out of a 97, Just waiting to be sandblasted and resealed.
0 2019/09/12 20:19:37
0 2019/09/12 20:14:07
Before
Before
0 2019/09/12 20:13:19
0 2019/09/12 20:06:41
0 2019/09/12 20:06:12
0 2019/09/12 19:53:27
0 2019/09/03 18:50:20
0 2019/09/03 18:50:18
0 2019/09/03 18:49:16
0 2019/09/03 18:48:53
0 2019/09/03 18:48:38
0 2019/09/03 18:31:36