Jeep Cherokee Forum
Connects to this hard line below and just to the right of the MAP sensor.
Connects to this hard line below and just to the right of the MAP sensor.
0 2016/08/02 21:53:36
Other end fitted to a hard line.
Other end fitted to a hard line.
0 2016/08/02 21:56:52
No idea where this plugs.
No idea where this plugs.
0 2016/08/02 21:57:01
A little bit of a gap, but maybe it's enough for my high idle...
A little bit of a gap, but maybe it's enough for my high idle...
0 2016/08/18 22:55:50
Cut it in by hand....get the axis to the correct diameter, then walk the butterfly down by slowly filing away the high spots....
Cut it in by hand....get the axis to the correct diameter, then walk the butterfly down by slowly filing away the high spots....
0 2016/08/18 22:56:26
0 2016/08/18 22:57:12
looking good! toit like a toiger.
looking good! toit like a toiger.
0 2016/08/18 22:57:26
Cut a new gasket...bolt her down
Cut a new gasket...bolt her down
0 2016/08/18 22:57:46
The red one. These 4 sit right behind your battery on the passenger side.
The red one. These 4 sit right behind your battery on the passenger side.
0 2016/08/18 23:02:14
0 2016/08/18 23:19:36
0 2016/08/18 23:19:50
You can kind of see the damage to the track bar bushing.
You can kind of see the damage to the track bar bushing.
0 2016/08/19 22:29:15
Frame side of the track bar.
Frame side of the track bar.
0 2016/08/19 22:29:52
Something doesn't look right....
Something doesn't look right....
0 2016/08/19 22:30:13
Hole isn't wallowed out - good news.
Hole isn't wallowed out - good news.
0 2016/08/19 22:30:28
This is the washer for the bolt through the track bar bushing. It saw quite a load, eh?
This is the washer for the bolt through the track bar bushing. It saw quite a load, eh?
0 2016/08/19 22:30:59
0 2016/08/19 22:32:35
This is the bolt - as I was tightening it, something felt wrong, so I backed it out. My guess is that the DW really stressed the bolt and it couldn't take another torquing.
This is the bolt - as I was tightening it, something felt wrong, so I backed it out. My guess is that the DW really stressed the bolt and it couldn't take another torquing.
0 2016/08/19 22:33:04
I chased the threads in the nut, but they still looked off, so I decided not to try to torque into it. Off to Lowes to buy a new grade 8 bolt, washer and nut. (Home Depot's fastener selection never ceases to disappoint....)
I chased the threads in the nut, but they still looked off, so I decided not to try to torque into it. Off to Lowes to buy a new grade 8 bolt, washer and nut. (Home Depot's fastener selection never ceases to disappoint....)
0 2016/08/19 22:42:36
Since you don't have the bracket to hold the nut in place, you've got to get your wrench in there like this.
Since you don't have the bracket to hold the nut in place, you've got to get your wrench in there like this.
0 2016/08/19 22:44:23
Knuckle side of the drag link.
Knuckle side of the drag link.
0 2016/08/19 22:44:58
Pitman arm side. I should have replaced this joint just because, but the replacement I purchase from O'Reilly was misboxed and I had to reinstall this one.
Pitman arm side. I should have replaced this joint just because, but the replacement I purchase from O'Reilly was misboxed and I had to reinstall this one.
0 2016/08/19 22:45:35
All 4 looked like this.
All 4 looked like this.
0 2016/08/19 22:53:16
New Moog bushings.
New Moog bushings.
0 2016/08/19 22:53:40
0 2024/05/19 20:17:14