Jeep Cherokee Forum
0 2016/06/19 16:07:48
Bolt it all up
Bolt it all up
0 2016/06/19 16:07:59
Make sure that black plastic chain guide is in place
Make sure that black plastic chain guide is in place
0 2016/06/19 16:08:16
Alternator bracket cleaned up.
Alternator bracket cleaned up.
0 2016/06/19 16:09:10
0 2016/06/19 16:09:15
0 2016/06/19 16:09:21
Old fan clutch
Old fan clutch
0 2016/06/19 16:09:30
New fan clutch
New fan clutch
0 2016/06/19 16:09:37
0 2016/06/19 16:09:44
0 2016/06/19 16:09:51
0 2016/06/19 16:10:06
0 2016/06/19 16:10:14
New harmonic balancer...note that this one doesn't have cracks in the rubber!
New harmonic balancer...note that this one doesn't have cracks in the rubber!
0 2016/06/19 16:11:18
0 2016/06/19 16:11:23
Torque specs
Torque specs
0 2016/06/19 16:11:32
Water pump goes on
Water pump goes on
0 2016/06/19 16:11:46
0 2016/06/19 16:11:53
0 2016/06/19 16:12:11
0 2016/06/19 16:12:18
0 2016/06/19 16:12:37
0 2016/06/19 16:12:43
0 2016/06/19 16:12:48
0 2016/06/19 16:13:00
0 2016/06/19 16:24:16
0 2016/06/19 16:24:45
The original bolt holding on the harmonic balancer was too short to get started to push the new balancer on, so off to Lowes to buy a longer one, to get it started.
The original bolt holding on the harmonic balancer was too short to get started to push the new balancer on, so off to Lowes to buy a longer one, to get it started.
0 2016/06/19 16:24:56
0 2016/06/19 16:25:07
Then, you put some man into it and it snaps off. In the crank. Not cool
Then, you put some man into it and it snaps off. In the crank. Not cool
0 2016/06/19 16:25:40
0 2016/06/19 16:25:54
0 2016/06/19 16:31:45
0 2016/06/19 16:31:55
The new radiator was from a newer year donor vehicle and the tranny oil line fittings didn't match.
The new radiator was from a newer year donor vehicle and the tranny oil line fittings didn't match.
0 2016/06/19 16:32:42
Let's buy a new one.
Let's buy a new one.
0 2016/06/19 16:33:56
Loosely attache the connector back together so you can see the wire pairs. As you clip the wires, only do one wire on each side and verify by testing continuity on the clipped wires. Strip the wires, slide a piece of heat shrink on one side.
Loosely attache the connector back together so you can see the wire pairs. As you clip the wires, only do one wire on each side and verify by testing continuity on the clipped wires. Strip the wires, slide a piece of heat shrink on one side.
0 2016/06/25 20:40:43
The infamous ground connectors.
The infamous ground connectors.
0 2016/06/25 20:40:54
These three are on the engine side of the harness
These three are on the engine side of the harness
0 2016/06/25 20:41:00
Solder the pair together.
Solder the pair together.
0 2016/06/25 20:41:14
These are the chassis side of the harness
These are the chassis side of the harness
0 2016/06/25 20:41:21
Co
Co
0 2016/06/25 20:41:31
0 2016/06/25 20:41:40