Jeep Cherokee Forum
0 2021/04/15 18:05:41
0 2021/04/17 21:54:39
That's how the faceplate will look one I recess the bezel into it.
That's how the faceplate will look one I recess the bezel into it.
0 2021/04/17 22:08:56
Side view. I'll be laying some plexiglass overtop when finished.
Side view. I'll be laying some plexiglass overtop when finished.
0 2021/04/17 22:09:16
Trimmed down.
Trimmed down.
0 2021/04/17 22:26:52
Cigarette lighter brackets cut to size
Cigarette lighter brackets cut to size
0 2021/04/17 22:28:55
Both side by side unmodified
Both side by side unmodified
0 2021/04/17 22:30:08
Mockup front
Mockup front
0 2021/04/17 22:31:07
Mockup rear
Mockup rear
0 2021/04/17 22:32:06
Mockup
Mockup
0 2021/04/17 22:47:24
0 2021/04/18 10:01:03
0 2021/04/18 10:01:56
0 2021/04/18 10:02:29
0 2021/04/18 11:15:56
0 2021/04/18 11:16:32
0 2021/04/18 17:25:19
0 2021/04/18 17:26:26
0 2021/04/18 17:26:52
0 2021/04/18 17:30:53
0 2021/04/20 18:57:22
0 2021/04/20 18:58:22
Theres enough clearance behind the mini cluster to get these eyelets in. Even though the other way looks cleaner, I will probably go this route since it's practically how the connection was made from the factory.
Theres enough clearance behind the mini cluster to get these eyelets in. Even though the other way looks cleaner, I will probably go this route since it's practically how the connection was made from the factory.
0 2021/05/01 18:04:38
I can also run the eyelets inside. But the problem I have here is I believe it will not make a connection, or if it does, it wont be a good enough connection. This configuration also raises the gauges slightly.
I can also run the eyelets inside. But the problem I have here is I believe it will not make a connection, or if it does, it wont be a good enough connection. This configuration also raises the gauges slightly.
0 2021/05/01 18:04:56
I bought these LED lights a while ago because they were on clearance and they are going to be perfect for this. They have an adhesive backing, and will match the main cluster as i plan on swapping those to LED's also.
I bought these LED lights a while ago because they were on clearance and they are going to be perfect for this. They have an adhesive backing, and will match the main cluster as i plan on swapping those to LED's also.
0 2021/05/01 18:14:35
This is probably how they will look wired in.
This is probably how they will look wired in.
0 2021/05/01 18:15:08
I am just going to route the wires through the factory light hole.
I am just going to route the wires through the factory light hole.
0 2021/05/01 18:15:26
I still have to drill a hole on the bottom gauge for the machine screw that supllies power to the "TU" terminal (anyone have clarification what this is?)
I still have to drill a hole on the bottom gauge for the machine screw that supllies power to the "TU" terminal (anyone have clarification what this is?)
0 2021/05/01 18:30:01
97+ kickplate inside of a -96.
97+ kickplate inside of a -96.
0 2021/05/01 19:04:34
Size differences between the two.
Size differences between the two.
0 2021/05/01 19:05:27
0 2021/05/26 11:47:41
0 2021/05/26 11:48:13
0 2021/05/26 11:49:50
0 2021/05/27 19:40:19
0 2021/05/29 13:38:50
0 2021/05/29 13:41:12
I labeled the hoses and electrical connections to stay organized.
I labeled the hoses and electrical connections to stay organized.
0 2021/05/29 13:41:54
I labeled the electrical connector too
I labeled the electrical connector too
0 2021/05/29 13:43:22
And so the fun begins. I started pulling the corrosponding wire out of the loom since im relocating the reservoir to the other side. Its not all too clear, but the blue wire with the qhite stripe is included inside of a heatshrink that is spliced and bigtailed from the factory. All I did was just turn it around180° at that point, and extended the wire. Unfortunately i couldnt locally find the same color coded wire, so I ended up with solid blue of the same gauge.
And so the fun begins. I started pulling the corrosponding wire out of the loom since im relocating the reservoir to the other side. Its not all too clear, but the blue wire with the qhite stripe is included inside of a heatshrink that is spliced and bigtailed from the factory. All I did was just turn it around180° at that point, and extended the wire. Unfortunately i couldnt locally find the same color coded wire, so I ended up with solid blue of the same gauge.
0 2021/05/29 13:44:54
Here you can see where I soldered and added heatshrink tubing to the extention. You can also see I am pulling the windshield washer hose out of the main wiring harness. The rubber was in decent shape, but I do not understand why Chrystler deaigned it like this.
Here you can see where I soldered and added heatshrink tubing to the extention. You can also see I am pulling the windshield washer hose out of the main wiring harness. The rubber was in decent shape, but I do not understand why Chrystler deaigned it like this.
0 2021/05/29 13:48:38
0 2021/05/29 13:51:20