Jeep Cherokee Forum
0 2022/02/06 18:14:46
0 2022/02/06 18:14:48
0 2022/02/06 18:19:19
0 2022/02/06 18:19:21
0 2022/02/06 18:19:24
0 2022/02/21 16:26:42
This is what's called a shoulder bolt. I believe its hardened steel because its black (like impact sockets) and the shoulder part is not black so I'm guessing it's a soft metal sleeve pressed over the actual bolt. Anyhow, the shoulder is half inch in diameter and I believe an inch in length, I'll double check later.
This is what's called a shoulder bolt. I believe its hardened steel because its black (like impact sockets) and the shoulder part is not black so I'm guessing it's a soft metal sleeve pressed over the actual bolt. Anyhow, the shoulder is half inch in diameter and I believe an inch in length, I'll double check later.
0 2022/02/21 16:26:49
0 2022/02/21 16:30:14
Time to drill the smaller out to 1/2 inch. This bracket sits ontop of the taper of the rivet.
Time to drill the smaller out to 1/2 inch. This bracket sits ontop of the taper of the rivet.
0 2022/02/21 16:32:15
This is how much shoulder is leftover after the width of the two plates...
This is how much shoulder is leftover after the width of the two plates...
0 2022/02/21 16:32:23
Which is perfect enough for a fender washer.
Which is perfect enough for a fender washer.
0 2022/02/21 16:32:32
G
G
0 2022/02/26 17:45:00
G
G
0 2022/02/26 17:45:03
G
G
0 2022/02/26 17:45:07
G
G
0 2022/02/26 17:45:11
0 2022/02/28 08:18:23
0 2022/03/05 19:20:10
0 2022/03/05 19:28:17
0 2022/03/05 19:28:21
0 2022/03/05 19:28:25
0 2022/03/05 19:28:28
0 2022/03/05 19:44:51
0 2022/03/05 19:45:08
0 2022/03/05 19:47:19
0 2022/03/05 19:47:26
MAP sensor can be flipped upside down and put back together with longer screws and spacers.
MAP sensor can be flipped upside down and put back together with longer screws and spacers.
0 2022/03/05 19:51:20
Top view.
Top view.
0 2022/03/05 19:51:28
This may be able to be used and it would prevent the use of the spacers.
This may be able to be used and it would prevent the use of the spacers.
0 2022/03/05 19:51:32
Before.
Before.
0 2022/03/05 19:54:35
After.
After.
0 2022/03/05 19:54:43
You can see the fitting installed right next to the TB hole.
You can see the fitting installed right next to the TB hole.
0 2022/03/05 20:00:36
And once it's removed...
And once it's removed...
0 2022/03/05 20:00:44
It's still too high. Ill have to shave it down and plug it. It may be different with the horseshoe intake but this is what I'm working with for now.
It's still too high. Ill have to shave it down and plug it. It may be different with the horseshoe intake but this is what I'm working with for now.
0 2022/03/05 20:00:51
Mocked up. You can see how the sensors are all now oriented towards the driver's side of the intake, right where the TJ harness cover will be.
Mocked up. You can see how the sensors are all now oriented towards the driver's side of the intake, right where the TJ harness cover will be.
0 2022/03/05 20:03:11
The cable bracket fits right under the fuel rail. I originally though I would have to use a TB spacer to move it above the fuel rail if i wanted to do this but all I will have to is notch the arm just a bit so the butterfly valve can return back to idle.
The cable bracket fits right under the fuel rail. I originally though I would have to use a TB spacer to move it above the fuel rail if i wanted to do this but all I will have to is notch the arm just a bit so the butterfly valve can return back to idle.
0 2022/03/05 20:03:19
Ill have to shave down a little bit of the plastic so its not resting on top of the fuel rail at idle.
Ill have to shave down a little bit of the plastic so its not resting on top of the fuel rail at idle.
0 2022/03/05 20:03:26
0 2022/03/05 20:26:02
0 2022/03/05 20:26:05
0 2022/03/05 20:26:07
0 2022/03/05 20:26:10