YJ Dana 30 in my 1990 XJ
#1
Newbie
Thread Starter
Join Date: May 2011
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
YJ Dana 30 in my 1990 XJ
I found this Dana Model 30 front axle with an Aussie Locker and 4.56 gears for $600 bucks. The axle is out of a 87 YJ. I need to know if it will be a bolt on install or a ***** of an install, or not possible at all. I have a 1990 XJ. Picture of the axle is attached.
Thanks.
Thanks.
#2
you sure that's not a tj front the yj is a leaf sprung jeep if it is a tj it should be a bolt in but if it is a yj leaf axle you will have to put your control arm brackets and spring mounts on that axle
hope this helps and good luck
hope this helps and good luck
#4
Seasoned Member
Join Date: May 2010
Location: Dillsburg, PA
Posts: 320
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: I6
I don't know what's up with that housing. Doesn't really look like a TJ axle, doesn't really look like a YJ axle either. Sounds like it has good internals (gears and locker) though. If it is a YJ axle, it'll be a high pinion unit and all the internals will swap into the high pinion housing that is currently in your XJ. That's probably the route that i would take...
#5
CF Veteran
Join Date: May 2011
Location: EAFB, SD
Posts: 1,381
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0 HO
well just looking at it i can tell you its not a YJ. its a coil over 4 link just like the XJ and has a HP so it should be fine.
#6
CF Veteran
Join Date: Jun 2010
Location: Flint/Asheville
Posts: 2,501
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 HO
^ This is a YJ axle.
^this is a XJ axle
What you have there looks to me like a YJ axle with custom 4 link brackets welded on. So it probably wont bolt into an XJ. The CAD thing isnt that important cause you can convert it to later model axle shafts, Might already have shafts in it idk.
#7
Seasoned Member
Join Date: May 2010
Location: Dillsburg, PA
Posts: 320
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: I6
I respectfully disagree. A CAD XJ axle will have the passenger side UCA mount cast into the CAD portion of the axle. That one has tabs welded onto the tube for the control arms. Also, the coil spring platforms are in front of the tubes. Never seen that before.
Trending Topics
#8
there is a guy in the for sale section of this forum that has an axle from a cherokee that is geared and locked for 650 that might be the best route for you givin all the great observations from all the wonderful people on this GREAT SITE!!!!
#9
Newbie
Thread Starter
Join Date: May 2011
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Yj
the guy tells me its from his YJ and he added coil springs. He is willing to take 300 for it so I am thinking of buying and switching gears and locker into mine. I dont think I can buy gears and locker for anywhere close to 300.
#10
CF Veteran
Join Date: Mar 2009
Location: Visalia, Kalifornia, ussa
Posts: 2,750
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
Buy it for the gears and locker. Even if the gears are trashed, you will have a carrier and locker for when you get good gears. Remember you still have to regear the rear end BEFORE you can use 4WD.
Thread
Thread Starter
Forum
Replies
Last Post
extrashaky
Other Vehicles. Other Jeep models & cars and trucks of other makes
17
06-17-2023 03:57 PM
Austindude2015
Cherokee Chat
17
12-28-2020 05:12 PM
Lightning_19k
Modified XJ Cherokee Tech
14
10-03-2015 09:52 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)