select trac transfer case
Thread Starter
Member
Joined: May 2011
Posts: 139
Likes: 0
From: alabama
Year: 1989
Model: Cherokee
Engine: 4.0
Have an 85 select trac cherokee with the 2.8 engine the transfer case just seems 2 want 2 transfer power 2 the front wheels and not the rear the rear is welded up is there anyway I can lock the transfer case in 2 where both the front and rear will pull it has what looks 2 be a vacum actuator ?? Will a 231 transfer case bolt up 2 the transmission it has the factory auto in it any help will be greatly appreciated
Originally Posted by baxj89
Have an 85 select trac cherokee with the 2.8 engine the transfer case just seems 2 want 2 transfer power 2 the front wheels and not the rear the rear is welded up is there anyway I can lock the transfer case in 2 where both the front and rear will pull it has what looks 2 be a vacum actuator ?? Will a 231 transfer case bolt up 2 the transmission it has the factory auto in it any help will be greatly appreciated
Thread Starter
Member
Joined: May 2011
Posts: 139
Likes: 0
From: alabama
Year: 1989
Model: Cherokee
Engine: 4.0
Well if me using the number 2 instead of the words to and too is confusing to u then why are u even commenting on this post. Obviously u have no knowledge of the select track or should I say the np 229 to clairify it......... but thanks anyways for the advice
Originally Posted by baxj89
Well if me using the number 2 instead of the words to and too is confusing to u then why are u even commenting on this post. Obviously u have no knowledge of the select track or should I say the np 229 to clairify it......... but thanks anyways for the advice
Thread Starter
Member
Joined: May 2011
Posts: 139
Likes: 0
From: alabama
Year: 1989
Model: Cherokee
Engine: 4.0
No that's. Not what I was asking. When the transfer case is in 4wd hi or lo it dosent let the rear wheels pull the front just pulls it will switch from driver side wheel to passenger side wheel but if u put it in 2 wd the rear works . From what I read so far when u put the transfer case in 4wd lo its supposed to make the front and rear pull just at different speeds I guess the transfer case is not going into low range is there some way to lock the transfer case into lo. Range were both front and rear will pull???
4 low locks the TC into 50/50 torque split front and rear. this is a mechanical lock so if you are not getting any power to the rear (be careful to seriously verify this) then you will likely need to pull the TC apart. You cannot be locked into front only for 4 low, so if youre in 4 low and getting power to an axle then you are definitely in, but something else is up
Senior Member
Joined: Dec 2009
Posts: 682
Likes: 0
From: Elk River, Minnesota
Year: 1989
Model: Cherokee
Engine: 4.0
Is this all you do is come on to these forums to argue with everyone? Damn near every post by you is either full of poor advice or incorrect information, and I am not talking about just this board.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
InitialForce
Modified XJ Cherokee Tech
9
Jul 5, 2022 12:17 AM
pantallica20@aol.com
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
4
Oct 1, 2015 02:58 PM
BlvdKreeper
Cherokee Chat
5
Oct 1, 2015 06:34 AM
csspencer
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
4
Sep 30, 2015 08:32 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)



