What did you do to your Cherokee today?
CF Veteran
Join Date: Aug 2012
Location: oregon
Posts: 1,592
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0 ho 99 intake ps pump 1" tb spacer 62mm bored tb eletric fans and more
Both :-( I have the trans mount loose and the motor mounts loose and can't get to them from top or bottom I have all types of swivels ect and can't get to it from the bottom and the trans tunnel is to tight to get a socket and ratchet on from the top...
So....
So....
CF Veteran
Join Date: Sep 2011
Location: Frederick, MD
Posts: 10,447
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
This is what worked for me. I also replaced those bolts with hex heads afterwards!
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,957
Received 1,545 Likes
on
1,252 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Loosen them BEFORE any other engine to trans bolts.
CF Veteran
Join Date: Feb 2013
Location: Justin, TEXAS
Posts: 1,802
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
I stood on top of my valve cover and reached back there with a thin wrench(mine were hex heads though) good luck!
After my second interview at KIA today I am just dropping the transfercase and just pulling the motor and trans together... I don't feel like wasting anymore time messing with those littler ****ers
yes its spray painted. camoflouge sand. unfortunately i ran over a gallon of oil on the highway and oil has splattered everywhere and wont come off
they are fluffy and comfortable but my driver side one broke after use. i only weigh 150lbs. FYI also any fancy tactical seat covers for Tj/YJ wont fit over it. they are too fluffy
Junior Member
Join Date: Jun 2014
Location: South Jersey
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L
Finished mine up yesterday. Leak was caused by a section of the gasket dropping into the pan when I muscled the pan back in place. Only had to drop it an inch or two to refit it. Good luck with the dipstick bolt on the engine!
Mill
Senior Member
Join Date: May 2014
Location: Iroquois Ontario Canada
Posts: 946
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
I have been putting off replacing the flex plate for some time now. I bought it the same week I picked up the Cherokee, but have procrastinated ever since. Now that I have most of the metal work done, and the lift kit installed there isn't much else to do before I "have to" start working on the mechanical stuff.
CF Veteran
Join Date: Apr 2011
Location: Indianapolis
Posts: 4,825
Likes: 0
Received 2 Likes
on
2 Posts
Year: '99 and '91
Model: Cherokee
Sold the 4.88 gears I bought (D30/8.8) actually made $50 off that.
Will probably start gathering stuff to patch the holes in my floor pan. What kind if seam sealer stuff am I looking for to seal up the floor pans? I plan on welding them but I doubt my weld will be leak proof.
Will probably start gathering stuff to patch the holes in my floor pan. What kind if seam sealer stuff am I looking for to seal up the floor pans? I plan on welding them but I doubt my weld will be leak proof.
☠ CF Sheriff ☠
Sold the 4.88 gears I bought (D30/8.8) actually made $50 off that.
Will probably start gathering stuff to patch the holes in my floor pan. What kind if seam sealer stuff am I looking for to seal up the floor pans? I plan on welding them but I doubt my weld will be leak proof.
Will probably start gathering stuff to patch the holes in my floor pan. What kind if seam sealer stuff am I looking for to seal up the floor pans? I plan on welding them but I doubt my weld will be leak proof.
i used this: http://3mcollision.com/products/seal...ige-08310.html