My '91 Briarwood
#256
Member
Thread Starter
#258
Member
Thread Starter
Time for another update:
Got some Bilstein 5125s installed, front driveshaft is reinstalled, drivers side leaf spring pack replaced, fender flares removed, and 33s put on.
Did some wheeling before I put the 33s on and took the fender flares off. Going wheeling this weekend!
Got some Bilstein 5125s installed, front driveshaft is reinstalled, drivers side leaf spring pack replaced, fender flares removed, and 33s put on.
Did some wheeling before I put the 33s on and took the fender flares off. Going wheeling this weekend!
The following users liked this post:
ijeeep (02-27-2021)
#259
Member
Thread Starter
Update for the year
Removed the ABS **** under the hood and installed a brake booster and master cylinder for a 99 GC.
(no pics :P)
Rebuilt the transfercase again. This time added the Boostwerks tcase shifter linkage.
Replaced AW4 shift solenoids as well
Right before I replaced the 33" KM2s.
Got some new tires!
Water pump needed replacing again
Finally trimmed the fenders!
Discovered some new noises since I put these nice new quiet tires on; rear drive shaft had a vibration at freeway speeds and sounds like Ive got a bad u joint in one of the axle shafts up front.
Got some new u joints for the front axle shafts coming and I have 2 front driveshafts being rebuilt at a drive shaft shop.
I also ordered some steel fender armor and flares from Dirtbound Offroad. Can't wait to get those on!
Removed the ABS **** under the hood and installed a brake booster and master cylinder for a 99 GC.
(no pics :P)
Rebuilt the transfercase again. This time added the Boostwerks tcase shifter linkage.
Replaced AW4 shift solenoids as well
Right before I replaced the 33" KM2s.
Got some new tires!
Water pump needed replacing again
Finally trimmed the fenders!
Discovered some new noises since I put these nice new quiet tires on; rear drive shaft had a vibration at freeway speeds and sounds like Ive got a bad u joint in one of the axle shafts up front.
Got some new u joints for the front axle shafts coming and I have 2 front driveshafts being rebuilt at a drive shaft shop.
I also ordered some steel fender armor and flares from Dirtbound Offroad. Can't wait to get those on!
#260
Member
Thread Starter
Passenger front wheel hub assembly was trashed. I did replace the ujoints on that axle shaft when I replaced the hub assembly.
Went to Bridgeport for some fun.
Transfercase started acting odd on the way back from there. Ended up pulling the tcase again and fixing stuff I messed up. All fixed now!
Also replaced the master cylinder since my brakes felt weird. Brakes are MUCH better. Guess the master cylinder I swapped in was bad or I didnt bleed it right.
The 2 driveshafts I had rebuilt recently have vibrations over 60MPH so I dropped them off with the shop that rebuilt them to have them figure it out.
My fender armor is also here, just need to finish painting them and slap them on.
Went to Bridgeport for some fun.
Transfercase started acting odd on the way back from there. Ended up pulling the tcase again and fixing stuff I messed up. All fixed now!
Also replaced the master cylinder since my brakes felt weird. Brakes are MUCH better. Guess the master cylinder I swapped in was bad or I didnt bleed it right.
The 2 driveshafts I had rebuilt recently have vibrations over 60MPH so I dropped them off with the shop that rebuilt them to have them figure it out.
My fender armor is also here, just need to finish painting them and slap them on.
The following users liked this post:
ijeeep (02-27-2021)
#261
Member
Thread Starter
Done a couple things since my last update - replaced the fuel pump, had a shop diagnose and repair an issue I couldn't figure out, and had some new wheels installed.
Waiting on this weather to calm down so I can go wheel the damn thing.
Waiting on this weather to calm down so I can go wheel the damn thing.
The following users liked this post:
ijeeep (02-27-2021)
#263
Member
Thread Starter
The following 2 users liked this post by Crusher16:
Battle (03-08-2021),
unidentifiedbomb (03-14-2021)
The following users liked this post:
Crusher16 (03-15-2021)
#267
Member
Thread Starter
Updates:
Did some more wheeling
And got rid of the coil spring spacers and softballs and replaced them with the JKS ACOS
Did some more wheeling
And got rid of the coil spring spacers and softballs and replaced them with the JKS ACOS
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)