Problems After Lift Install......
#1
Senior Member
Thread Starter
Join Date: Oct 2008
Location: Orlando FL.
Posts: 544
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 242 6cyl
Problems After Lift Install......
Alright well i finished my lift today and everything was fine the only problem i had was breaking a upper shock bolt.......Now after checking everything and some measuring i see that the passenger side is just about an inch shorter then the driver's side everything looks nice and tight.....This has me stumped and was wondering if anybody else has had this problem happen to them before or if anybody has a clue what it could be?!?!?!?
Thanks.......
Thanks.......
#4
Registered Users
Join Date: Nov 2008
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0l
thats weird..... there usually higher on the passengers side.... a lot of new vehicles come like that from the factory cause its the ditch side....... are your coils sitting in the buckets correctly? are the isolators in on both sides?
#6
Senior Member
Thread Starter
Join Date: Oct 2008
Location: Orlando FL.
Posts: 544
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 242 6cyl
From what i could tell everything on all 4 corners is where it's supposed to be....Now i just measured it again and it's only off my 3/4 of an inch so im thinking maybe it's starting to settle?!??!
Im also wondering if it could be from not having an allignment done yet which im doin tomm......
Trending Topics
#8
Seasoned Member
Join Date: Sep 2008
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
For the front coils, did you make sure that they were "clocked" correctly?
The bottom end of the coil is supposed to drop down into a hole/slot/groove thing, IIRC.
The bottom end of the coil is supposed to drop down into a hole/slot/groove thing, IIRC.
#9
Senior Member
Thread Starter
Join Date: Oct 2008
Location: Orlando FL.
Posts: 544
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 242 6cyl
Im also thinking when i did my "test" of articulation i drove up the the hill on the driver's side only and not the passenger side maybe i need to drive up the passenger side as well to settle it a little better lol?!?!?!
#10
Senior Member
Join Date: Dec 2008
Posts: 543
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1987
Model: Cherokee
Engine: 4.0 soon to be gc ho 4.0
uneven ground. it looks level its not. most jeeps have a issue like this , im sure its not that noticeable but if everythings right then go buy .75 coil spacer and put it on the side thats unlevel. thats 3/4 inch
#12
Registered Users
Join Date: Nov 2008
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0l
if you just put the lift in then i would not worry..... its still got tons of time to settle... just take it down a dirt road and bounce the **** out of it... thats what i'd do!!!
#13
Senior Member
Thread Starter
Join Date: Oct 2008
Location: Orlando FL.
Posts: 544
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 242 6cyl
Well i took her out to the woods today to test everything out and it looks like it has settled down some so everything is all good......
Thanks guys........
Thanks guys........
Thread
Thread Starter
Forum
Replies
Last Post
95cherokee89
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
59
10-16-2015 03:17 AM
Jose Calderon
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
17
09-17-2015 08:57 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)