Problem getting into 4 low!!!!
#1
Newbie
Thread Starter
Join Date: Apr 2013
Location: Medford OR
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Year: 01
Model: Cherokee
Engine: 4.0L
Problem getting into 4 low!!!!
I found out I have a NP242 TC where a NP231 use to be, my selector only goes 2HI, 4HI, N, 4LO on the console. So now I can get it in to 2HI, 4HI/PT, 4HI/FT, and N, but I cant pull it back far enough to get 4LO any suggestions on what should be done to achieve 4LO?
Mac
Mac
#2
CF Veteran
Join Date: Oct 2011
Location: Bakersfield CA
Posts: 1,268
Likes: 0
Received 1 Like
on
1 Post
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Not positive but whomever did this may have not taken the shifter and linkage for the 242 and just reused the 231 linkage, they may not be the same. Or you'll need to open up the hole that the shifter is in and locate a 242 shift cover.
But I would check that the linkage is adj. properly first.
But I would check that the linkage is adj. properly first.
#3
Newbie
Thread Starter
Join Date: Apr 2013
Location: Medford OR
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Year: 01
Model: Cherokee
Engine: 4.0L
I believe the linkage is from the 231, I though about cutting into the cover and shifter metal follower so that i could move the shifter back another inch or 2, was hoping there would be another way.
#5
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,875
Received 1,526 Likes
on
1,238 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Bare minimum get the curved piece with the slots in it from a 242 Jeep. It's under the shift bezel.
#7
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,875
Received 1,526 Likes
on
1,238 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
No link. Under the shift bezel is the "rail " that you're looking for. self explanatory.
Trending Topics
#8
Newbie
Thread Starter
Join Date: Apr 2013
Location: Medford OR
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Year: 01
Model: Cherokee
Engine: 4.0L
Oh ok i got ya, the one in there now has a notch on the left side, I think I might be able to just take that one out and cut some of the metal off the back of it, that would allow my shifter to go back another inch. if that fails, i have seen some ppl loose the Z linkage and make the simple link to the TC
Thread
Thread Starter
Forum
Replies
Last Post
xjwolfman
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
8
08-26-2020 12:59 PM
Dannymac1216
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
13
09-08-2015 06:28 AM
Jeepy11
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
2
09-03-2015 09:32 AM
Jicki Rough
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
09-02-2015 09:36 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)