01 XJ Vacuum Leak - Tea Kettle Whistle
#1
Junior Member
Thread Starter
Join Date: Dec 2011
Location: State College, PA
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0 I6
01 XJ Vacuum Leak - Tea Kettle Whistle
I know this has been asked before, but I'm trying to gain more info than what I've already read..
Since I bought my 01 XJ classic back in November it has intermittently made a loud, high-pitched whistling noise.. It only happens when I let off the gas, and goes away when I give it any gas at all. Sometimes it will continue to whistle while idling. Another thing to note is that the whistle seems to stop when my electric fan kicks on.
I've read that loose intake/exhaust manifold bolts or a bad mani gasket can cause this.. what's the best way to access these bolts to check if they're tight? Is there anything else I should check that may be causing the whistle? Thanks in advance.
Since I bought my 01 XJ classic back in November it has intermittently made a loud, high-pitched whistling noise.. It only happens when I let off the gas, and goes away when I give it any gas at all. Sometimes it will continue to whistle while idling. Another thing to note is that the whistle seems to stop when my electric fan kicks on.
I've read that loose intake/exhaust manifold bolts or a bad mani gasket can cause this.. what's the best way to access these bolts to check if they're tight? Is there anything else I should check that may be causing the whistle? Thanks in advance.
#2
When I replaced my manifold(s) i got the same thing. Didn't seat properly at first. The bolts came loose in a few miles. I just torqued them back down. Make sure you ONLY do this in ye proper order. Start by running your engine and spraying carb cleaner on the intake junction to the head to see if it's leaking there. Then try all other vacuum lines. Hope this helps.
#3
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 17 Likes
on
17 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
You can listen for the spot with a short length of hose held to your ear. Another trick is to go around with short little bursts of starting fluid. If you hit a vacuum leak, the sound of the engine will change. Good luck!
That rear manifold bolt has a habit of loosening. On anything like that you NEVER want to tighten only one. It can warp/bend, even crack things. If I found that any that where easy to reach where loose, I'd pull the air cleaner and tighten them all, starting in the middle and working out towards the ends. I'd go over three times, a tad tighter each time. It's a bear of a spot to get a torque wrench on them all. Just don't ape on it. If its firm and not turning, no point in going on to break it, a REAL *****. The rearmost bolt underneath takes a little doing, but it can be done with the right extension. For that very back one by the firewall I use way long extensions (18"), with a swivel at the socket.
(Check your motor mount while the air cleaner is off)
That rear manifold bolt has a habit of loosening. On anything like that you NEVER want to tighten only one. It can warp/bend, even crack things. If I found that any that where easy to reach where loose, I'd pull the air cleaner and tighten them all, starting in the middle and working out towards the ends. I'd go over three times, a tad tighter each time. It's a bear of a spot to get a torque wrench on them all. Just don't ape on it. If its firm and not turning, no point in going on to break it, a REAL *****. The rearmost bolt underneath takes a little doing, but it can be done with the right extension. For that very back one by the firewall I use way long extensions (18"), with a swivel at the socket.
(Check your motor mount while the air cleaner is off)
#5
Junior Member
Thread Starter
Join Date: Dec 2011
Location: State College, PA
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0 I6
Went in yesterday and checked all the manifold bolts.. low and behold the rearmost bolt on the bottom was loose. I tightened it and now the whistle is a different pitch.. I'm thinking the gasket needs replaced
#6
CF Veteran
Join Date: Sep 2011
Location: Riviera, Texas
Posts: 4,172
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1998 Sport
Model: Cherokee
Engine: 4.0
It is very possible that it does need to be replaced. Do yourself a favor. Get a can of starting fluid and spray it around the vacuum hoses and where you had the vac leak on the intake and make sure that it was the only vac leak that you have. When you spray the starting fluid and you hit a spot that is leaking your idle will change.
Last edited by RTorrez1; 04-07-2012 at 02:18 PM.
#7
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 17 Likes
on
17 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
Yea. You'll want a new gasket of you are replacing your exhaust manifold because you didn't just tighten the bolts. (then check again with starting fluid)
Trending Topics
#9
Junior Member
Thread Starter
Join Date: Dec 2011
Location: State College, PA
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0 I6
Not sure what you're saying.. as far as I know the manifold is ok?? I checked all the bolts, starting on the inner ones and working outward.
#11
CF Veteran
Join Date: Nov 2011
Location: State College, PA
Posts: 1,469
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 I6
#15
CF Veteran
Join Date: Nov 2011
Location: State College, PA
Posts: 1,469
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 I6
the OP's Jeep and I are familiar with one another, his manifold isn't leaky.
BTW, his jeep is a bastard, and I've shed my blood on it more than I have on mine haha
BTW, his jeep is a bastard, and I've shed my blood on it more than I have on mine haha