Jeep Cherokee Forum
0 2015/10/29 00:01:29
0 2015/10/29 00:01:09
0 2015/10/29 00:00:35
Spent alot of time on the lower part thinking and getting it right the first time, the first side took me 2-3 hours. the second side I tackled took about 45 minutes.
Spent alot of time on the lower part thinking and getting it right the first time, the first side took me 2-3 hours. the second side I tackled took about 45 minutes.
0 2015/10/28 23:54:33
But with the fenders that we fabbed up, those will cover all my "sins" so mostly it just has to be strong and seal up correctly against the elements.
But with the fenders that we fabbed up, those will cover all my "sins" so mostly it just has to be strong and seal up correctly against the elements.
0 2015/10/28 23:53:56
Rear fenders, big project, scary for me at first, not much experience with welding thin stuff. Also "body work" another scary part.
Rear fenders, big project, scary for me at first, not much experience with welding thin stuff. Also "body work" another scary part.
0 2015/10/28 23:53:26
Slip yoke eliminator kit, new shift selector plate, 4WD linkage fabrication, shortened driveshaft, correct speedo calibration set up all done by M.I.T in El Cajon. I added 2 degree shims for the correct pinion angle and all is good!
Slip yoke eliminator kit, new shift selector plate, 4WD linkage fabrication, shortened driveshaft, correct speedo calibration set up all done by M.I.T in El Cajon. I added 2 degree shims for the correct pinion angle and all is good!
0 2015/10/28 23:38:02
0 2015/10/28 23:28:18
I went with a 6.5 Clayton package, what a nice kit!
I went with a 6.5 Clayton package, what a nice kit!
0 2015/10/28 23:27:43
Several months ago I pulled the trigger on the lift kit, but I did not cover the choice or the install.
Several months ago I pulled the trigger on the lift kit, but I did not cover the choice or the install.
0 2015/10/28 23:27:15
0 2015/10/19 23:47:59
0 2015/10/19 23:41:38
0 2015/10/19 23:39:12
0 2015/10/19 23:38:47
0 2015/10/19 23:36:56
0 2015/10/19 23:32:33
0 2015/10/19 23:26:31
0 2015/10/19 23:19:49
0 2015/10/19 23:18:29
Bought some Dirtbound front fenders. took 7 months to get them, the owner made up for the wait by throwing in some water jet cutting, " Cummins" is now where the Cherokee logo used to be.
Bought some Dirtbound front fenders. took 7 months to get them, the owner made up for the wait by throwing in some water jet cutting, " Cummins" is now where the Cherokee logo used to be.
0 2015/10/19 23:14:12
0 2015/10/18 00:31:10
0 2015/10/18 00:27:45
0 2015/10/18 00:25:07
0 2015/10/18 00:23:54
0 2015/10/18 00:19:48
Had to figure a way to hold the throttle cable down at the bottom of the slot.
Had to figure a way to hold the throttle cable down at the bottom of the slot.
0 2015/10/18 00:17:47
0 2015/10/18 00:17:02
0 2015/10/18 00:16:15
I gave it some bracing due to the leverage and fot pedal action it will endure.
I gave it some bracing due to the leverage and fot pedal action it will endure.
0 2015/10/18 00:12:35
0 2015/10/18 00:09:11
0 2015/10/18 00:07:52
0 2015/10/18 00:07:31
0 2015/10/18 00:05:36
I started some "eyeball engineering"
I started some "eyeball engineering"
0 2015/10/18 00:04:12
0 2015/10/18 00:03:41
I needed a bracket to hold the original throttle cable, I needed it to be generally where I was holding it in this photo.
I needed a bracket to hold the original throttle cable, I needed it to be generally where I was holding it in this photo.
0 2015/10/18 00:01:00
0 2015/10/18 00:00:03
0 2015/10/17 23:58:23
0 2015/10/17 23:51:35
I started some "eyeball engineering" The bracket started by shaping and slotting square tubing.
I started some "eyeball engineering" The bracket started by shaping and slotting square tubing.
0 2015/10/17 23:50:50