Jeep Cherokee Forum
0 2019/03/05 06:24:10
0 2019/03/05 06:25:18
0 2019/03/05 06:27:49
0 2019/03/05 06:33:31
0 2019/03/05 06:34:05
0 2019/03/05 06:34:52
0 2019/03/05 06:36:39
0 2019/03/05 06:37:50
0 2019/03/05 06:39:25
0 2019/03/05 06:43:43
0 2019/04/18 07:10:38
0 2019/04/18 07:10:53
0 2019/04/18 07:11:45
0 2019/04/18 07:11:56
0 2019/04/18 07:12:10
0 2019/04/18 07:12:25
0 2019/04/18 07:12:39
0 2019/04/18 07:12:50
0 2019/04/18 07:13:06
On the trails again with warmer weather around
On the trails again with warmer weather around
0 2019/04/18 07:18:49
Spark plug replacement
Spark plug replacement
0 2019/04/18 07:19:11
0 2019/04/20 05:53:45
0 2019/04/20 05:54:42
0 2020/11/15 15:40:25
0 2020/11/15 15:40:32
0 2021/12/26 16:19:21
Closeup of the c clip
Closeup of the c clip
0 2021/12/26 16:19:28
Swapping long arms onto my old 2000 XJ
Swapping long arms onto my old 2000 XJ
0 2022/01/06 05:41:57
0 2022/01/06 05:42:01
My first XJ. 4.0 auto 4x4 on a 3 inch lift.
My first XJ. 4.0 auto 4x4 on a 3 inch lift.
0 2022/01/06 08:29:27
A view of my rocker panel corrosion that I let progress for way too long
A view of my rocker panel corrosion that I let progress for way too long
0 2022/01/06 09:17:55
0 2022/01/06 09:20:18
Ready for replacements
Ready for replacements
0 2022/01/06 09:20:22
0 2022/01/06 09:31:22
The air chisel chewed right through the spot welds and made peeling the floor pan away quite easy. I had used a hammer and chisel in the past for this… Decided to dab some POR-15 I had left from a previous project on the inside of the frame rail.
The air chisel chewed right through the spot welds and made peeling the floor pan away quite easy. I had used a hammer and chisel in the past for this… Decided to dab some POR-15 I had left from a previous project on the inside of the frame rail.
0 2022/01/10 19:13:46
I opted for a 1/2 floor pan off Quadratec. I laid the pan in on top of the frame rail and traced the edges of the rails with a sharpie on the underside. This gave me an idea where to drill holes to be plug welded to the frame.
I opted for a 1/2 floor pan off Quadratec. I laid the pan in on top of the frame rail and traced the edges of the rails with a sharpie on the underside. This gave me an idea where to drill holes to be plug welded to the frame.
0 2022/01/10 19:13:49
It took quite a while to get to this point, but all finished. It fits very nicely. I did get some help from a friend that welds much more often than I do. I also burned in a new seat mount!
It took quite a while to get to this point, but all finished. It fits very nicely. I did get some help from a friend that welds much more often than I do. I also burned in a new seat mount!
0 2022/01/10 19:13:52
Floor pan cut out
Floor pan cut out
0 2022/01/10 19:13:55
0 2022/01/10 19:25:12
0 2022/01/10 19:27:54