Jeep Cherokee Forum
Got the tank out to get it ready for the sump. Been sitting on my patio full of water. Need to get on that.
Got the tank out to get it ready for the sump. Been sitting on my patio full of water. Need to get on that.
0 2017/03/09 02:01:13
Playing around with a homemade press brake.
Playing around with a homemade press brake.
0 2017/03/09 02:02:11
0 2017/03/09 02:02:58
0 2017/03/09 02:03:29
I sealed the inside with an epoxy paint. Moisture.... Waited for over a month then one Saturday the weather cooperated and I was able to spray it out.
I sealed the inside with an epoxy paint. Moisture.... Waited for over a month then one Saturday the weather cooperated and I was able to spray it out.
0 2017/03/09 02:03:55
Patience..... This has frustrated me to the point that I almost smashed it... More then once....
Patience..... This has frustrated me to the point that I almost smashed it... More then once....
0 2017/03/09 02:04:18
Heater box is ready.
Heater box is ready.
0 2017/03/09 02:04:45
Base gaskets were leaking. So I put a big bore kit on him and paid a shop to have the heads reworked.
Base gaskets were leaking. So I put a big bore kit on him and paid a shop to have the heads reworked.
0 2017/03/09 02:04:53
0 2017/04/09 13:16:09
0 2017/04/09 13:16:30
I got the door functioning again. Ran some 23. Haven't welded anything that thin in a long time. Burned through three times before I got steady.
I got the door functioning again. Ran some 23. Haven't welded anything that thin in a long time. Burned through three times before I got steady.
0 2017/04/09 13:17:10
0 2017/04/09 13:17:58
After I lowered the front end. I think that's where I want my ride height. Will see after I add some weight. If it looks good after that I can setup my drivetrain angles .
After I lowered the front end. I think that's where I want my ride height. Will see after I add some weight. If it looks good after that I can setup my drivetrain angles .
0 2017/04/09 13:18:45
Before
Before
0 2017/04/09 13:20:19
Got the sump on. Thought I took more pictures...
Got the sump on. Thought I took more pictures...
0 2017/04/09 13:21:00
0 2017/04/21 08:41:50
I got started on the cross member for the engine. Looks crude now but I've got a long way to go before I can clean it up.
I got started on the cross member for the engine. Looks crude now but I've got a long way to go before I can clean it up.
0 2017/05/07 21:40:00
0 2017/05/07 21:41:07
0 2017/05/07 21:41:34
The engine is going forward two inches and down one. Once I get that set I will begin the steering. Drag link is in the way of the oil pan. Can't cut the oil pan down. The rod to pan clearance at the front is just above tolerance. I might go with a rack and pinion setup:-$
The engine is going forward two inches and down one. Once I get that set I will begin the steering. Drag link is in the way of the oil pan. Can't cut the oil pan down. The rod to pan clearance at the front is just above tolerance. I might go with a rack and pinion setup:-$
0 2017/05/07 21:41:44
Had to lay down some practice beads. Ending up running out of gas on the cross member and had to call it quits. Got the seat mounted in where I want it so I can begin setting up he rollbar. I also put the car up on stands and leveled it out. Took a while to get it level and don't want to take it down until all angles are set.
Had to lay down some practice beads. Ending up running out of gas on the cross member and had to call it quits. Got the seat mounted in where I want it so I can begin setting up he rollbar. I also put the car up on stands and leveled it out. Took a while to get it level and don't want to take it down until all angles are set.
0 2017/05/07 21:41:56
While I'm deciding on what to do with the steering putting in the roll bar will keep me busy. ALOT of measure, check ,measure, cut, test fit, in and out. In and out. I ended up finding some foam pads too lay down on the floor boards to make the in and out easier.
While I'm deciding on what to do with the steering putting in the roll bar will keep me busy. ALOT of measure, check ,measure, cut, test fit, in and out. In and out. I ended up finding some foam pads too lay down on the floor boards to make the in and out easier.
0 2017/05/22 08:05:30
0 2017/05/22 08:05:51
That armrest used to be tan. My first attempt at painting vinyl. Came out really well. Have since done almost all of the interior peices.
That armrest used to be tan. My first attempt at painting vinyl. Came out really well. Have since done almost all of the interior peices.
0 2017/05/22 08:06:24
I also got my plates today.
I also got my plates today.
0 2017/05/22 18:35:00
0 2017/06/26 00:48:55
0 2017/06/26 00:49:34
0 2017/06/26 00:50:13
0 2017/06/26 13:00:04
0 2017/06/26 13:00:27
0 2017/08/15 02:49:00
0 2017/08/15 02:49:14
0 2017/08/15 08:43:19
I have the engine set. Threw a bunch of weight at the car to get the ride height where It may be after everything is asembled
I have the engine set. Threw a bunch of weight at the car to get the ride height where It may be after everything is asembled
0 2017/09/11 07:10:55
Got rid of the clock and added a tach.
Got rid of the clock and added a tach.
0 2017/09/11 07:11:17
The interior is coming together nicely.
The interior is coming together nicely.
0 2017/09/11 07:11:46
The Jeep's bumper. Long way from complete.
The Jeep's bumper. Long way from complete.
0 2017/09/11 07:12:13
Got the engine all set. Will get a better pic later.
Got the engine all set. Will get a better pic later.
0 2017/09/27 14:27:27
The LCAs were paper thin and flimsy. Wasn't having that..
The LCAs were paper thin and flimsy. Wasn't having that..
0 2017/09/27 14:28:14
Wish I had time to clean it all up.
Wish I had time to clean it all up.
0 2017/09/27 14:29:37