Jeep Cherokee Forum
0 2015/10/28 12:22:59
0 2015/10/28 12:24:00
0 2016/01/25 16:08:59
Haven't updated in a while. I reinforced my track bar.
Haven't updated in a while. I reinforced my track bar.
0 2016/02/01 20:17:43
Did a cow run and will be doing another on Saturday.
Did a cow run and will be doing another on Saturday.
0 2016/02/01 20:18:11
We put a stroker in Daves Renix
We put a stroker in Daves Renix
0 2016/02/01 20:18:21
0 2016/02/02 16:06:36
0 2016/02/02 16:07:10
0 2016/02/02 16:07:15
0 2019/07/04 12:29:14
0 2019/07/04 12:30:12
0 2019/07/04 12:31:24
0 2019/07/04 12:32:21
0 2019/07/04 12:36:36
I started him up and let him run for about 30 minutes. Im a few weeks out from a complete suspension and steering overhaul. Gearing up for a Fordyce run this summer.
I started him up and let him run for about 30 minutes. Im a few weeks out from a complete suspension and steering overhaul. Gearing up for a Fordyce run this summer.
0 2016/03/31 22:04:28
Got rid of the mudd. Dont want that crap falling my eyes while im working underneath.
Got rid of the mudd. Dont want that crap falling my eyes while im working underneath.
0 2016/04/28 14:39:57
0 2016/04/28 14:40:16
New plates came with the pink. I will probably get custom plates later on.
New plates came with the pink. I will probably get custom plates later on.
0 2016/05/04 20:40:52
Daves jeep gets a built 30 today
Daves jeep gets a built 30 today
0 2016/06/04 14:21:58
0 2016/06/19 22:22:47
0 2016/06/29 19:26:45
0 2016/07/17 16:35:27
0 2016/07/17 16:35:42
0 2016/07/17 16:36:04
0 2016/07/17 16:36:19
0 2016/07/17 16:36:28
0 2016/07/17 16:36:54
0 2016/07/17 16:37:15
0 2016/07/17 16:37:36
0 2016/07/17 16:38:00
Slowly gathering little parts while saving up for the headers. Correct lug nuts, hood release cable, headlight door and rotors/wheel bearings to get it back to five lug.
Slowly gathering little parts while saving up for the headers. Correct lug nuts, hood release cable, headlight door and rotors/wheel bearings to get it back to five lug.
0 2016/07/17 16:39:25
The previous builder drilled out the old rotors to work with the centerlines and the 8.8.
The previous builder drilled out the old rotors to work with the centerlines and the 8.8.
0 2016/07/17 16:43:17
Haven't got to turn a wrench since the move. I needed it. I got it up off the ground and leveled it out. Not easy on a crooked ass floor.
Haven't got to turn a wrench since the move. I needed it. I got it up off the ground and leveled it out. Not easy on a crooked ass floor.
0 2016/07/17 16:44:55
Look at that pinion angle.
Look at that pinion angle.
0 2016/07/17 16:49:33
Good the thing they never finished the 8.8 swap. Im going to replace those perches with some longer ones to help with axle wrap and junk those hacked up U-bolts.
Good the thing they never finished the 8.8 swap. Im going to replace those perches with some longer ones to help with axle wrap and junk those hacked up U-bolts.
0 2016/07/17 16:50:39
Got the pinion angle dummied in. Im far from getting it set in stone. The engine/tranny centerline was about 8 degrees down before I leveled it out. 5 degrees leveled out. Need it to be around 3. Got to get a trans crossmember fabbed up and decide on tire sizes. Then I can get the numbers to set the pinion angle. The current crossmember is a peice of 1x1 square stock. Didn't get a pic but it takes up alot of ground clearance and impedes on the route foe exhaust pipes.
Got the pinion angle dummied in. Im far from getting it set in stone. The engine/tranny centerline was about 8 degrees down before I leveled it out. 5 degrees leveled out. Need it to be around 3. Got to get a trans crossmember fabbed up and decide on tire sizes. Then I can get the numbers to set the pinion angle. The current crossmember is a peice of 1x1 square stock. Didn't get a pic but it takes up alot of ground clearance and impedes on the route foe exhaust pipes.
0 2016/07/17 16:55:20
Got rid of ^those lug nuts. Seeing those on the centerlines made me twitch.
Got rid of ^those lug nuts. Seeing those on the centerlines made me twitch.
0 2016/07/17 17:38:43
Now i can sleep at night.
Now i can sleep at night.
0 2016/07/17 17:45:03
Now I can sleep at night.
Now I can sleep at night.
0 2016/07/17 17:45:52
Pulled all the grill plastics off.
Pulled all the grill plastics off.
0 2016/07/17 17:46:35