Mark this thread as Unsold
FS[PacSouthWest]: High Pinion Dana 30 axle with manual disconnect 3.08's
#1
Member
Thread Starter
Join Date: Dec 2012
Location: Santa Cruz, CA
Posts: 176
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
High Pinion Dana 30 axle with manual disconnect 3.08's
I picked up the axle off of craigslist being advertised as 3.73 gears, was told it had been re geared. It has NOT been, it has stock 3.08 gears in it.
All complete from brakes to brakes, newer ball joints and brakes are good.
Comes with a complete conversion from vacuum to manual disconnect. Which I was going to delete and use later one piece shafts.
I will sell the disconnect cable and fork with all other parts without axle if desired, I will ship those parts too.
Make me an offer on manual disconnect parts if you want, local pickup only in Santa Cruz CA.
Pinion gears look excellent and all appears to be in good working order.
$75.
This is the cast housing which is supposed to be much stronger then the later model housings as well. If not sold I will build it for my jeep when I get a little bit of extra funds.
Thanks.
All complete from brakes to brakes, newer ball joints and brakes are good.
Comes with a complete conversion from vacuum to manual disconnect. Which I was going to delete and use later one piece shafts.
I will sell the disconnect cable and fork with all other parts without axle if desired, I will ship those parts too.
Make me an offer on manual disconnect parts if you want, local pickup only in Santa Cruz CA.
Pinion gears look excellent and all appears to be in good working order.
$75.
This is the cast housing which is supposed to be much stronger then the later model housings as well. If not sold I will build it for my jeep when I get a little bit of extra funds.
Thanks.
#3
Junior Member
Join Date: Dec 2012
Location: Northeast P.A
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
Year: 88-95-96-01
Model: Cherokee
Engine: 4.0
damn. wish you were on east coast..
This is exactly what im looking for.. I want the CAD- I have and aussie in front in my LP D30 and wanted a HP30 CAD so I can unlock the axle,and keep that locker from making all kinds of noise. almost like a homebrew ox setup. . Also wanted to upgrade to a HP. from the CV axle low pinion.
This is exactly what im looking for.. I want the CAD- I have and aussie in front in my LP D30 and wanted a HP30 CAD so I can unlock the axle,and keep that locker from making all kinds of noise. almost like a homebrew ox setup. . Also wanted to upgrade to a HP. from the CV axle low pinion.
#4
Newbie
Join Date: Dec 2011
Location: Pittston, PA
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
damn. wish you were on east coast..
This is exactly what im looking for.. I want the CAD- I have and aussie in front in my LP D30 and wanted a HP30 CAD so I can unlock the axle,and keep that locker from making all kinds of noise. almost like a homebrew ox setup. . Also wanted to upgrade to a HP. from the CV axle low pinion.
This is exactly what im looking for.. I want the CAD- I have and aussie in front in my LP D30 and wanted a HP30 CAD so I can unlock the axle,and keep that locker from making all kinds of noise. almost like a homebrew ox setup. . Also wanted to upgrade to a HP. from the CV axle low pinion.
Thread
Thread Starter
Forum
Replies
Last Post
southfloridajeeps
Modified XJ Cherokee Tech
32
03-04-2023 01:10 PM
RickJames Bish
Modified XJ Cherokee Tech
5
09-02-2015 03:22 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)