steering turns more to the left than the right?
#1
Senior Member
Thread Starter
Join Date: Aug 2011
Location: Santa Rosa, CA
Posts: 710
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
steering turns more to the left than the right?
So i just replaced my track bar end with the pivot joint its supposed to come with ( apparently the person before me swapped it for a bushing joint.. )
and it appears to have fixed the popping noise coming from my steering.
but now ( not sure if it was like this before ) the steering goes more to the left then the right
to go over my setup i have a 96 jeep cherokee sport
It has a 4.5 in long arm kit by rough country ( included the trackbar i was talking about )
and i have a currie drag link and tie rod setup
also i have a durango steering box with a c-rok brace behind it
and somewhat of a drop pitman arm not sure what brand maybe just off of a zj
here are some pictures to show you how much were talking about.
heres full turn driver
heres the bump stop on the passenger knuckle, full turn driver ( you can also see the pivot joint i put on the end of the trackbar the silver piece upper right )
heres full turn passenger
heres the bump stop on the driver knuckle, full turn passenger
you can see that turned full driver the bump stop is about 1/4-1/2 inch ( it does touch at full lock but when you let go of the wheel it bounces back a bit )
and turned full passenger the bump stop is more like 1-1 1/2 inches
what would cause this??
and it appears to have fixed the popping noise coming from my steering.
but now ( not sure if it was like this before ) the steering goes more to the left then the right
to go over my setup i have a 96 jeep cherokee sport
It has a 4.5 in long arm kit by rough country ( included the trackbar i was talking about )
and i have a currie drag link and tie rod setup
also i have a durango steering box with a c-rok brace behind it
and somewhat of a drop pitman arm not sure what brand maybe just off of a zj
here are some pictures to show you how much were talking about.
heres full turn driver
heres the bump stop on the passenger knuckle, full turn driver ( you can also see the pivot joint i put on the end of the trackbar the silver piece upper right )
heres full turn passenger
heres the bump stop on the driver knuckle, full turn passenger
you can see that turned full driver the bump stop is about 1/4-1/2 inch ( it does touch at full lock but when you let go of the wheel it bounces back a bit )
and turned full passenger the bump stop is more like 1-1 1/2 inches
what would cause this??
#2
CF Veteran
Join Date: Dec 2010
Location: Spanish Fork, Utah
Posts: 2,366
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: Renix 4.0L
You might have your steering gear not centered in your steering gear box. My bet, that is. Research it! And align it.
#3
Senior Member
Thread Starter
Join Date: Aug 2011
Location: Santa Rosa, CA
Posts: 710
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
#5
CF Veteran
Join Date: Dec 2010
Location: Spanish Fork, Utah
Posts: 2,366
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: Renix 4.0L
Originally Posted by 96rokee
ima do some measuring tmrw morning and figure out how bad it really is.
#7
Senior Member
Thread Starter
Join Date: Aug 2011
Location: Santa Rosa, CA
Posts: 710
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
yes.
the guy replaced the pivot joint with a bushing joint. and well the bushing joint didnt pivot like the pivot joint.
and it would put stress on the bolt in the bolt hole untill it made it out of round.
then the bolt would start popping up and down as i turned..
so today when i got the new pivot joint i drilled a new hole cuz the other 2 were ovaled out..
but if this one ovals out ill have to figure out some sort of drop bracket oor something?? any suggestions in case that becomes what i need to do??
the guy replaced the pivot joint with a bushing joint. and well the bushing joint didnt pivot like the pivot joint.
and it would put stress on the bolt in the bolt hole untill it made it out of round.
then the bolt would start popping up and down as i turned..
so today when i got the new pivot joint i drilled a new hole cuz the other 2 were ovaled out..
but if this one ovals out ill have to figure out some sort of drop bracket oor something?? any suggestions in case that becomes what i need to do??
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Aug 2011
Location: Santa Rosa, CA
Posts: 710
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
Thread
Thread Starter
Forum
Replies
Last Post
southfloridajeeps
Modified XJ Cherokee Tech
32
03-04-2023 01:10 PM
aroundincircles
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
5
10-06-2015 11:12 AM
neocracka
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
8
09-05-2015 06:50 PM
MyJeepIsATyrant
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
09-04-2015 10:36 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)