Rear drive shaft question. Measurement needed.
#1
Member
Thread Starter
Join Date: Mar 2013
Location: McMinnville Oregon
Posts: 115
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Rear drive shaft question. Measurement needed.
So I just did my lift and I wanted to wait a while before installing my SYE. It can't wait. The driveline vibes are horrid. I'm hoping to find someone with nearly the same setup so I can get a measurement prior to doing the SYE so I can have the driveshaft already. I plan to run a front drive shaft on the rear I just need to know which one to get. So here is my setup. Hopefully someone can help by giving me a rough measurement.
6.5" lift.
Standard length SYE (not the ultra short) the one I have is a rugged ridge.
8.25 rear.
A friend has a few front drive lines. Just don't know which to get. I want to replace the joints in it prior to putting it in. Thanks a ton in advance for any help.
6.5" lift.
Standard length SYE (not the ultra short) the one I have is a rugged ridge.
8.25 rear.
A friend has a few front drive lines. Just don't know which to get. I want to replace the joints in it prior to putting it in. Thanks a ton in advance for any help.
#2
Junior Member
Join Date: Nov 2014
Location: U.S/CAN DMZ
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0 I6
Don't mean to butt in but if someone has the measurement for a 4.5 inch lift as well that'd be helpful, I have a 8.25 as well.
Last edited by Drstrangelove; 04-10-2015 at 10:35 AM. Reason: Spelling isn't a strong suit
#6
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
Yup. I theory a front DS is good up to 6.5" to use or a ZJ would be better. OP, do a search on google for jeep front DS sizes and go out and measure what you got now. Yes the SYE kit makes all the difference and you may not get an answer until you install one. You have to remember that all jeeps are different
#7
Senior Member
Join Date: Oct 2012
Location: Gainesville,FL
Posts: 989
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
I'm running a 6.5 inch long arm lift with a RR mega short SYE and a C8.25 and from yoke to yoke it was 38.5. I had to order a custom made driveshaft for my application. But here's a list of the driveshaft sized for Jeeps.
XJ 89/01 4.0 Automatic 30.660 inches
XJ 89/01 4.0 Manual 29.250 inches
ZJ 1993 4.0 Automatic 30.530
ZJ 93/95 5.2 Automatic 32.870 w/o CV
ZJ 94/95 5.2 A500 30.625 w/o CV
ZJ 94/95 4.0 A500 w/o CV
ZJ 93/96 4.0 Manual
ZJ 93/96 4.0, 5.2 31.875 w/ 231, 242
ZJ 93/95 4.0 Manual 30.000 w/231
ZJ 93/96 5.2 33.000 w/ 231
ZJ 96/98 5.2, 5.9 31.250 w/ 249 & Model 30
ZJ 1996 5.2 Automatic 32.875 w/ 249 & Model 30
ZJ 96/98 4.0 33.000 w/ 242
ZJ 96/97 4.0 Automatic 31.250
ZJ 1996 5.2 Automatic 30.750 w/ 249 & Model 30
ZJ 96/98 4.0 33.500 w/ 249
WJ 99/00 4.0 34.625 52099497AD
WJ 99/00 4.7 33.250 52099498AD
WJ 01/04 4.0 34.625 52105884AA *
WJ 02/04 4.7 32.000 CV 52853500AB
XJ 89/01 4.0 Automatic 30.660 inches
XJ 89/01 4.0 Manual 29.250 inches
ZJ 1993 4.0 Automatic 30.530
ZJ 93/95 5.2 Automatic 32.870 w/o CV
ZJ 94/95 5.2 A500 30.625 w/o CV
ZJ 94/95 4.0 A500 w/o CV
ZJ 93/96 4.0 Manual
ZJ 93/96 4.0, 5.2 31.875 w/ 231, 242
ZJ 93/95 4.0 Manual 30.000 w/231
ZJ 93/96 5.2 33.000 w/ 231
ZJ 96/98 5.2, 5.9 31.250 w/ 249 & Model 30
ZJ 1996 5.2 Automatic 32.875 w/ 249 & Model 30
ZJ 96/98 4.0 33.000 w/ 242
ZJ 96/97 4.0 Automatic 31.250
ZJ 1996 5.2 Automatic 30.750 w/ 249 & Model 30
ZJ 96/98 4.0 33.500 w/ 249
WJ 99/00 4.0 34.625 52099497AD
WJ 99/00 4.7 33.250 52099498AD
WJ 01/04 4.0 34.625 52105884AA *
WJ 02/04 4.7 32.000 CV 52853500AB
Trending Topics
#9
Member
Thread Starter
Join Date: Mar 2013
Location: McMinnville Oregon
Posts: 115
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
I picked up a front shaft from a 5.2 zj at the yard this weekend. Measures around 33" collapsed. Around 37" extended. I'm hoping this will work.
Has anyone ever needed a different front driveshaft due to lift? Longer to make up for the lift?
Has anyone ever needed a different front driveshaft due to lift? Longer to make up for the lift?
#10
Senior Member
Join Date: Dec 2010
Location: Wekiva, FL
Posts: 888
Likes: 0
Received 2 Likes
on
2 Posts
Year: 99 sport
Model: Cherokee
Engine: 4.0 i6
I would recommend a front shaft from a v8 ZJ. All the ones I have seen (and what I am currently using) are splined front shafts. Which seem to me,that they must be stronger then the XJ front shaft which I have never seen splined.
Also,You can take the ZJ front shaft apart. Meaning the end with the ujoint that ties to the front axle will slide out of the end with the universal Joint that ties to the transfer case.
Then with an angle grinder you can cut the splines down to what works for you.
At 5.5 inches of lift with an 8.25 rear and the IRO HnT slip Yoke eliminator the ZJ shaft did not fit, it was to big. I had to cut down an inch of splines. Also now I'm close to 8 inches and it still works great.
At 6.5 inches I feel like a ZJ shaft will work for you with some cutting and your saving yourself alot of money.
Also,You can take the ZJ front shaft apart. Meaning the end with the ujoint that ties to the front axle will slide out of the end with the universal Joint that ties to the transfer case.
Then with an angle grinder you can cut the splines down to what works for you.
At 5.5 inches of lift with an 8.25 rear and the IRO HnT slip Yoke eliminator the ZJ shaft did not fit, it was to big. I had to cut down an inch of splines. Also now I'm close to 8 inches and it still works great.
At 6.5 inches I feel like a ZJ shaft will work for you with some cutting and your saving yourself alot of money.
#11
Member
Thread Starter
Join Date: Mar 2013
Location: McMinnville Oregon
Posts: 115
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
good information XJUSMC thanks. I'm hoping it will work. Bolts right up to the yoke/flange I got with my rugged ridge SYE.
#12
Everyone's running auto trans. I just ordered a 6.5 rough country for my 95 2 dr manual was hoping to get a shaft for when the kit shows up anyone know what I need with a rugged ridge sye kit ? Sorry if I'm high jacking (day 1)
#13
#14
Newbie
Join Date: Mar 2010
Location: Louisville Ky
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
i have 5.5 inch lift, with advance adapters sye.. i just ordered my drive shaft, should be here monday.. my measurement was 33.75. but remember EVERY set up is different.. so just because it works for mine, doesn't mean it will work for yours.
Thread
Thread Starter
Forum
Replies
Last Post
TwinTurboXj
Cherokee Chat
11
08-23-2015 12:45 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)