?? about grinding out backing plate for disc conversion
Thread Starter
Member
Joined: Jul 2009
Posts: 119
Likes: 0
From: British Columbia
Year: 1998
Model: Cherokee
Engine: 4.0
Is it possible to get the wrong ZJ parts??
I just picked up the disc brake assembly for my swap and so I decided to check how much I have to grind out. I have'nt quite started yet as I have to rebuild the brake parts, ( lots of rust and gunk ). Anyways I took my caliper to measure the axel tube and compare that to the hole in the backing plate. According to what I have, I have to grind out alot,( almost into the 4 bolt holes) and from all the pics I've seen it does'nt match up with what I have. Is the axel tube narrower at the backing plate end? The jeep I got it off of said it was a 94 grand, it had abs, does this make a difference ? Did I get something else by mistake? I'm trying to get all my info straight before I tear apart my jeep as it is my DD and I have to get it completed in 1 day.
Also I read somewhere that I can use D30 lugs. Is this true or better to get ZJ lugs.
Thank you for all the help.
Also I read somewhere that I can use D30 lugs. Is this true or better to get ZJ lugs.
Thank you for all the help.
Last edited by 98xjeeper; Jul 30, 2012 at 03:38 PM.
Junior Member
Joined: May 2008
Posts: 15,016
Likes: 11
From: +34° 25' 35.67", -81° 21' 12.04"
Year: 1993
Engine: 4.0
Yes, it narrows down at the end. You'll see when you pull the old backing plates off. You don't have to grind off a lot.
This is a picture of the end of an 8.25. The bolt pattern you see here is the same bolt pattern on the backing plates that you pulled off of the ZJ.
This is a picture of the end of an 8.25. The bolt pattern you see here is the same bolt pattern on the backing plates that you pulled off of the ZJ.
Last edited by Lowrange2; Jul 30, 2012 at 04:26 PM.
Seasoned Member
Joined: May 2011
Posts: 367
Likes: 1
Model: Cherokee
you can use ZJ studs if you're running stock wheels; im using ZJ studs with aluminum wheels and they work fine, but i do wish they were a little bit longer. i try to err towards the 'overkill/damn-sure' side when it comes to something that important lol.
the amount of material you have to grind is so miniscule that i didnt even measure anything; i just kept grinding away with a grinding stone until it fit nice & snug on the axle. took me about 5 minutes per side. you'll love em when your done though, stops on a dime and way less nosedive.
never heard anything about d30 studs... i cant imagine theyd be much longer, if any, but i couldnt say for sure.
the amount of material you have to grind is so miniscule that i didnt even measure anything; i just kept grinding away with a grinding stone until it fit nice & snug on the axle. took me about 5 minutes per side. you'll love em when your done though, stops on a dime and way less nosedive.
never heard anything about d30 studs... i cant imagine theyd be much longer, if any, but i couldnt say for sure.
Last edited by rompnXJ; Jul 30, 2012 at 05:50 PM.
Thread Starter
Member
Joined: Jul 2009
Posts: 119
Likes: 0
From: British Columbia
Year: 1998
Model: Cherokee
Engine: 4.0
Thanks guys, I just went out and got new pads, rotors and even parking brake shoes. Just have to get some calipers and maybe brake cables. Maybe I'll try to mod the cables I have, not sure yet.
Again, thanks for the input. I always check all my cherokee work with this forum.
Again, thanks for the input. I always check all my cherokee work with this forum.
CF Veteran
Joined: Jan 2011
Posts: 1,894
Likes: 4
From: Las Vegas
Year: 1999
Model: Cherokee
Engine: 4.0
Thread
Thread Starter
Forum
Replies
Last Post
mtoskippy
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
8
Sep 1, 2015 06:40 PM
cherokee01
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
10
Aug 30, 2015 05:04 AM
Cane
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
40
Aug 26, 2015 12:08 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
