What did you do to your Cherokee today?
CF Veteran
Joined: Mar 2011
Posts: 1,273
Likes: 1
From: South Bend, IN
Year: 1995
Model: Cherokee
Engine: 4.6 stroker
Member
Joined: Jul 2012
Posts: 154
Likes: 1
From: Albuquerque, NM
Year: 1988
Model: Cherokee
Engine: 4.0
Pulled out my flat rear leaf springs and removed the rear sway bar and put in a different set of leafs that ended up being flat too sigh. Also found a yakima rack to put on it too.
Moderator of Jeeps
Joined: Jul 2011
Posts: 21,029
Likes: 3
From: Frederick, MD from Cleveland, OH
Year: 1993 YJ Wrangler
Engine: 4.0 I6
Converted my '88 Renix to an open cooling system. Ten thousand thanks to Green2000 for the shop, tools, heater, time, and expertise. Pics will be in the build thread tomorrow. Too dark now.
Senior Member
Joined: Apr 2012
Posts: 735
Likes: 0
From: Los Banos CA
Year: 2000
Model: Cherokee
Engine: 4.0
Pulled out my center console to run my final set or RCAs for my future 2 amp setup. Now 3 sets of RCAs and two turn on wires. One on switch and one straight to power from deck. Just need to upgrade my power and ground wires to 4 gauge. One amp on switched trigger wire will be for sub. Deck trigger wire will be on my current 4 channel amp powering my speakers. Also finally took pics of completed home brew headlight wiring upgrade.
Last edited by 89cherokee2gtmudy; Nov 24, 2012 at 11:40 PM.
Senior Member
Joined: Jun 2012
Posts: 595
Likes: 0
From: Rome, GA
Year: 1990
Model: Cherokee
Engine: 4.0
Pulled out my center console to run my final set or RCAs for my future 2 amp setup. Now 3 sets of RCAs and two turn on wires. One on switch and one straight to power from deck. Just need to upgrade my power and ground wires to 4 gauge. One amp on switched trigger wire will be for sub. Deck trigger wire will be on my current 4 channel amp powering my speakers. Also finally took pics of completed home brew headlight wiring upgrade.
Attachment 157177
Attachment 157178
Attachment 157179
Attachment 157177
Attachment 157178
Attachment 157179
Senior Member
Joined: Jun 2012
Posts: 595
Likes: 0
From: Rome, GA
Year: 1990
Model: Cherokee
Engine: 4.0
Replaced my oil sending unit yesterday and my oil pressure readings are back to normal.
Drained the 10w-30 out and put 15w-40 in. The valve train noise isn't gone but, at least I they can hear me talking in the drive through now.
Later today when it gets above freezing (24 degrees at the moment), I'm going to replace my center console cover latch.
Drained the 10w-30 out and put 15w-40 in. The valve train noise isn't gone but, at least I they can hear me talking in the drive through now.
Later today when it gets above freezing (24 degrees at the moment), I'm going to replace my center console cover latch.
Banned
Joined: Oct 2012
Posts: 1,744
Likes: 2
From: USA
Year: 1998
Model: Cherokee
Engine: 4.0L i6
Front diff fluid change, water came out along with black sludge lol. Wire wheeled the chunks (yes, CHUNKS) of rust off of the diff cover, hit it with some Tremclad Rust Paint and spray can bedliner. Did an RTV gasket, first time working with it. I don't know why anyone would really have problems with it unless they got it all over their skin 
Used Permatex Ultra Black
Technically I didn't, but my fiancee did a drain 'n' fill on the poor old AX-15, finally got the MT-90 in it! Soooo much better shifting now, and less drag than that awful AC Delco Synchromesh/Lucas Transmission Fix goo I thought was a good idea. Couldn't help but laugh when she backed out the drain plug all the way and almost got oil in her face... my hand was already pushing the catch pan towards her haha
Used Permatex Ultra BlackTechnically I didn't, but my fiancee did a drain 'n' fill on the poor old AX-15, finally got the MT-90 in it! Soooo much better shifting now, and less drag than that awful AC Delco Synchromesh/Lucas Transmission Fix goo I thought was a good idea. Couldn't help but laugh when she backed out the drain plug all the way and almost got oil in her face... my hand was already pushing the catch pan towards her haha
Then you just reassemble with RTV and fill it via the fill hole?
For the AX-15, you just did a drain and fill? MT-90 is the tranny fluid of choice here?
☠ CF Sheriff ☠
Joined: Nov 2009
Posts: 15,197
Likes: 18
From: Aberdeen, MD
Year: 1995
Model: Cherokee
Engine: 4.0L HO I-6, 703 Injectors, Brown Dog Super Engine Mounts
Originally Posted by BimmerJeeper
For front Diff, you need to drain it by unbolting that "faceplate"?
Then you just reassemble with RTV and fill it via the fill hole?
For the AX-15, you just did a drain and fill? MT-90 is the tranny fluid of choice here?
I like to use a paper gasket with a very thin layer of rtv on each surface. Never had a leak that way, and don't have to wait to fill
CF Veteran
Joined: Apr 2011
Posts: 14,553
Likes: 1
From: Carrollton, GA
Year: 1994
Model: Cherokee
Engine: Inline 6 4.0L High Output
Originally Posted by BimmerJeeper
For front Diff, you need to drain it by unbolting that "faceplate"?
Then you just reassemble with RTV and fill it via the fill hole?
For the AX-15, you just did a drain and fill? MT-90 is the tranny fluid of choice here?
☠ CF Sheriff ☠
Joined: Nov 2009
Posts: 15,197
Likes: 18
From: Aberdeen, MD
Year: 1995
Model: Cherokee
Engine: 4.0L HO I-6, 703 Injectors, Brown Dog Super Engine Mounts
Originally Posted by Hamster
Replaced my oil sending unit yesterday and my oil pressure readings are back to normal.
Drained the 10w-30 out and put 15w-40 in. The valve train noise isn't gone but, at least I they can hear me talking in the drive through now.
Later today when it gets above freezing (24 degrees at the moment), I'm going to replace my center console cover latch.
Drained the 10w-30 out and put 15w-40 in. The valve train noise isn't gone but, at least I they can hear me talking in the drive through now.
Later today when it gets above freezing (24 degrees at the moment), I'm going to replace my center console cover latch.
I use 5w-30 year round.
☠ CF Sheriff ☠
Joined: Nov 2009
Posts: 15,197
Likes: 18
From: Aberdeen, MD
Year: 1995
Model: Cherokee
Engine: 4.0L HO I-6, 703 Injectors, Brown Dog Super Engine Mounts
Originally Posted by Hamster
Ok, I just gotta know. How did you get your grill out with your fog/driving lights still attached? I pulled every single screw I could find and it just won't let go.
Member
Joined: Jun 2012
Posts: 193
Likes: 1
Model: Cherokee
this was really yesterday. but, i scratch the crap out of my xj. but, it was fun. really just a pov video. but, it works.
looks like youtube jack with the video. because it looks like the camera is bouncing. it didn't do that before.
looks like youtube jack with the video. because it looks like the camera is bouncing. it didn't do that before.
Last edited by UPS rat; Nov 25, 2012 at 08:37 AM.
