Dana 44 question
07-22-2012, 01:42 AM
#1
Member
Thread Starter
Join Date: Jul 2012
Posts: 138
Likes: 0
Received 0 Likes
on
0 Posts
Dana 44 question
Hey all so if I landed a Dana 44 front axle for my jeep from a ford one of the older ones with lockers can I just cut all the mounts and long arms off my axle now and reeled everything to the new one or will I have to buy new stuff???
07-22-2012, 07:45 AM
#2
Been covered here many, many times.
Here's a link that you should bookmark and refer to often when planning/performing a Ford HP Dana44 swap.
http://77cj.littlekeylime.com/web_rs44.html
A lot depends on whether you want to run the axle in the stock (full-width) configuration or if you want to narrow it Grand Wagoneer width.
Something that is often overlooked in the planning phase of this project is wheel bolt patterns, give it some thought.
Here's a link that you should bookmark and refer to often when planning/performing a Ford HP Dana44 swap.
http://77cj.littlekeylime.com/web_rs44.html
A lot depends on whether you want to run the axle in the stock (full-width) configuration or if you want to narrow it Grand Wagoneer width.
Something that is often overlooked in the planning phase of this project is wheel bolt patterns, give it some thought.
07-22-2012, 07:56 AM
#3
CF Veteran
Join Date: Jun 2011
Location: Louisville,KY
Posts: 8,014
Likes: 0
Received 14 Likes
on
14 Posts
Model: Cherokee
If it was me i would just order a truss kit and the mounting tabs from http://www.tntcustoms.com/front.aspx
07-22-2012, 10:53 AM
#4
Member
Thread Starter
Join Date: Jul 2012
Posts: 138
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by andrewmp6
If it was me i would just order a truss kit and the mounting tabs from http://www.tntcustoms.com/front.aspx
07-22-2012, 10:54 AM
#5
Member
Thread Starter
Join Date: Jul 2012
Posts: 138
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SeriousOffroad
Been covered here many, many times.
Here's a link that you should bookmark and refer to often when planning/performing a Ford HP Dana44 swap.
http://77cj.littlekeylime.com/web_rs44.html
A lot depends on whether you want to run the axle in the stock (full-width) configuration or if you want to narrow it Grand Wagoneer width.
Something that is often overlooked in the planning phase of this project is wheel bolt patterns, give it some thought.
Here's a link that you should bookmark and refer to often when planning/performing a Ford HP Dana44 swap.
http://77cj.littlekeylime.com/web_rs44.html
A lot depends on whether you want to run the axle in the stock (full-width) configuration or if you want to narrow it Grand Wagoneer width.
Something that is often overlooked in the planning phase of this project is wheel bolt patterns, give it some thought.
07-22-2012, 04:27 PM
#6
CF Veteran
Join Date: Feb 2010
Location: Soddy Daisy TN
Posts: 5,420
Likes: 0
Received 0 Likes
on
0 Posts
Year: 97
Model: Cherokee
Engine: 4.0L
Depends on what it's out of because there are several versions. If it has cast wedges, 78-79 1/2 ton version, you can't cut them off and have to either retube it or use modified ford radius arms. On mine I used Rusty's lower control arm brackets and made my uppers, coil buckets came off another D30 I had and I modified a track bar mount off the same D30.
The truss strengthens the housing and the one they are referring to can have the mounts on it depending on how you order it.
The truss strengthens the housing and the one they are referring to can have the mounts on it depending on how you order it.
Thread
Thread Starter
Forum
Replies
Last Post
aa7kn
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
8
09-23-2015 09:08 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)