Homebrew Jeep Mods
06-06-2010, 06:39 PM
#331
hey where did you get those flat fender flares??? Ive been trying to find flat fenders for my XJ for months now ive seen quadratec is advertising them on the back of their summer catalog but when i checked online and even called they said they dont carry flat fender flares!?!?!?! Please help. if you made them, holy hell they look awesome and back to square one for me...
Meet square one.
Square one, this is Sparke.
06-07-2010, 11:48 AM
#332
CF Veteran
Join Date: Jul 2009
Location: New Jersey (Milltown, Lavallette, and Wayne)
Posts: 2,245
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0L I6
hey where did you get those flat fender flares??? Ive been trying to find flat fenders for my XJ for months now ive seen quadratec is advertising them on the back of their summer catalog but when i checked online and even called they said they dont carry flat fender flares!?!?!?! Please help. if you made them, holy hell they look awesome and back to square one for me...
06-07-2010, 09:01 PM
#333
Junior Member
Join Date: Jan 2010
Location: DC/Metro Area
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
hey thanks, yeah i was looking around there site later that night i wrote that reply and i saw they finally put them up. thanks for responding tho. Im planning on ordering them this week, ive been waiting for someone to come out with them for a while! cant wait til mine looks as good as yours!
06-08-2010, 11:39 AM
#335
Seasoned Member
Join Date: May 2010
Location: Wherever the AF sends me!!
Posts: 309
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0
Too bad I don't have the money while the deal is going on... but I will def. be looking at getting these if I can't find someone to make me up some tubed flat fender flares for mine...
06-09-2010, 07:53 AM
#338
CF Veteran
I'm right there with you worleste000. My exhaust consists of the exhaust manifold, pipe, cat, pipe, muffler, about 6" of pipe, then a turn down. No more rattle, and it doesn't drag with my departure angle.
06-09-2010, 01:51 PM
#339
Member
Join Date: May 2010
Location: Concho,AZ
Posts: 167
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1987
Model: Cherokee
Engine: 4.0
Heres my solution to the lack of cup holders in older XJ's.
Just a standard water bottle holder for a bike. All switches are usable with no interference. And it beats the plastic one u buy from the dealer. That i'm assuming would break if it was bumped at anything below freezing. Hey and it doesn't look to bad when its holding a drink and its +100F out
Just a standard water bottle holder for a bike. All switches are usable with no interference. And it beats the plastic one u buy from the dealer. That i'm assuming would break if it was bumped at anything below freezing. Hey and it doesn't look to bad when its holding a drink and its +100F out
Thats awesome I was just telling my wife today that was the only thing I didnt like about the jeep no cupholders!
06-11-2010, 08:26 AM
#340
CF Veteran
Join Date: Jun 2010
Location: Flint/Asheville
Posts: 2,501
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1995
Model: Cherokee
Engine: 4.0 HO
I use my gf as the cup holder lol
But i actually bought some door pockets of a guy on NAXJA and i use those when shes not there
But i actually bought some door pockets of a guy on NAXJA and i use those when shes not there
06-21-2010, 05:14 AM
#342
CF Veteran
Join Date: Jun 2009
Location: Las Vegas, NV
Posts: 1,415
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0L
A couple of my own....
Tube doors for my old cherokee. Being worry-some about getting them stolen in Las Vegas, Nevada...I welded some half inch steel rod to the bottom of the door. Basically bent the rod into a C shape and put a Limiting Strap on it and welded it to the door. Then bolted the other end of the limiting strap to the body under the trim below the dash...
Another shot with my custom speaker mounts with no doors :P
Also Daystars TJ vent switches nicely fit in the vents of 97-01 Cherokees (XJ) and no cutting is required for a clean switch install
Also some switches in place of the clock on my 91 XJ. switches bought from pepboys as a panel and the mounting is just sheet metal bent to fit inside...
Tube doors for my old cherokee. Being worry-some about getting them stolen in Las Vegas, Nevada...I welded some half inch steel rod to the bottom of the door. Basically bent the rod into a C shape and put a Limiting Strap on it and welded it to the door. Then bolted the other end of the limiting strap to the body under the trim below the dash...
Another shot with my custom speaker mounts with no doors :P
Also Daystars TJ vent switches nicely fit in the vents of 97-01 Cherokees (XJ) and no cutting is required for a clean switch install
Also some switches in place of the clock on my 91 XJ. switches bought from pepboys as a panel and the mounting is just sheet metal bent to fit inside...
06-21-2010, 06:45 AM
#343
Old Skewl CF like a Sir
Join Date: Feb 2008
Location: Fort Myers, FL
Posts: 4,355
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L High Output OBDII
^^ Nice.
On that note, since this is my 6th Jeep, and for the first time, one that doesn't have to double duty as a DD, I figured I'm finally gonna build my monster rig.
Since I took this I've cleaned it with a brushed look, and done switches/ 2 gauges. Other interior pieces are 4 points & gutted interior. Someday when I'm not lazy I'll actually make a half arsed build thread.
On that note, since this is my 6th Jeep, and for the first time, one that doesn't have to double duty as a DD, I figured I'm finally gonna build my monster rig.
Since I took this I've cleaned it with a brushed look, and done switches/ 2 gauges. Other interior pieces are 4 points & gutted interior. Someday when I'm not lazy I'll actually make a half arsed build thread.
06-21-2010, 01:24 PM
#344
CF Veteran
Join Date: Oct 2009
Location: Parrish
Posts: 1,487
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Comanche
Engine: 4.0
I made a false floor. It is kind of like 96_XJ's floor but taller and top access with cup holders.
Link to the thread
https://www.cherokeeforum.com/f58/ca...ization-50674/
Link to the thread
https://www.cherokeeforum.com/f58/ca...ization-50674/
06-24-2010, 07:50 PM
#345
Senior Member
Join Date: Jun 2009
Location: SW Colorado
Posts: 540
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0 6cyl
I made a false floor too! However it does look a little ghetto since i ran out of the carpet to cover it with haha. Plus is was all free since i got the wood out of a construction dumpster and i had the carpet scraps laying around. This is for the most part based off of 96_xj's design so all props go to him!!! 
DSC00939.jpg?t=1277426965
DSC00939.jpg?t=1277426965
