cleenrob

Picking up and IRO hack n tap with all bits in cludedoff a member

cleenrob

Picking up and IRO hack n tap with all bits in cludedoff a member

cleenrob

picked up a flush and fill kit/2 gallons of prestone long life 50/50 coolant/ toggle switch and some all rubber floor mats

gonna wire my fan contoler to set the fan on high via toggle switch..soon. its got a 12v switched lead thats "supposed" to got to tha A/C clutch to engage the fan on high when the a/c is on...but ive got my aux fan for that so i figure ill run 12v power to a switch and then to that lead so i can turn the fan on high when ever i want

tuesdays the day ill get my new cooling parts on

After ive got my cooling system under control ive got to replace my unit bearings and u-joints. and get my alt upgrade done...finally

cleenrob

just thought id give yall my current list of installed parts...

EDITED 8/29/15
suspension:

4.5'' RE coils
1.5''coil spacers
IRO double sheer track bar
Dukie disconnects(modded for 5.5'')
serious offroad on ton steering
b.lees 3 link
bilstein 5100 6.5'' of lift(rear)
bilstein 5150 12'' travel shocks(front)
front stem to eye adapters
rear sway bar mounts for BPE's
RC 3'' AAL
XJ stock main leaf AAL
home brew spring rebound clips
H.D off road shackle relocators
dakota shackles (1'' longer than stock)
Cooper Discoverer STT 33x12.50xR15
Summit 15x8 D-Windows(soon to have stock center caps)

performance:

volvo 960 cooling fan
modified xj fan shroud to fit volvo fan
volvo 960fan controller
SAAB 900 inline thermo-switch adapter
Porsche thermo-switch
indicator lights for fan operation
high fan over ride switch
home brew cowl snorkel
IAT relocation
60mm throttle body
703 neon injectors
APN header
Walker down pipe(no crush)
magnaflow cat
flowmasater 40 muffler
rustys mandrel bent 2.5'' tail pipe
Aux fan switch
robert shaw 195 thermostat
hesco hi flow t stat housing
flow kooler water pump
136 amp ZJ alternator
KelleysWiP battery cables
150 amp reset-able circuit breaker
ford explorer trans cooler

Armor/Recovery:

OEM t-case skid
OEM gas tank skid
C4x4 winch bumper with brush gaurd
smittybilt XRC10 winch
in cab winch controller
jcr nutstrips
jcr rock sliders
reciver shackle
hi-lift under back seat
off road base
33'' spare on a matching summit d-window


MISC:
trucklites
detours pillar brackets
olympus LED pods
good year all rubber floor mats
wood grain dash bezel
wood grain steering wheel cover
country wood grain doorpanels
recovered OHC with LED panels
Pioneer head unit wired properly
6.5'' jvc speakers(front)
stock00 speakers (rear)
q-logic kick panel speaker enclosures
ZJ front seats
00 xj back seat
ZJ console lid
98 trans shifter
ZJ shifter ****
280z hood vents
naipier precision products fender flares
red Gauge cluster/ shifter LEDS
home brew cup holder
doorless mod
captin tator tot
raptor tot
hood lift -from warrior products
np231j from a 2000 with 120k and and SYE already installed
custom rear double cardan drive shft

axles:

front
HP d30
4.10s
drilled/slotted rotors
solid diff cover
760s
timken hubs

rear
29 spline c8.25
4.10s
detroit
solid diff cover
zj disks

i thinks thats about it

current future plans in no particular order:

wj knuckle swap
frame stiffners
5.3 vortec swap
RE 3.5" leaves
rear doorless



some other stuff

cleenrob

Got my cooling parts in! I painted my hesco tstat housing already

I'm aiming to get it done tuesday.

cleenrob

Pics

cleenrob

just ordered 2 timken hub bearings and an OBDII bluetooth adapter

cleenrob

Getting a set of zj disks from BigDavid

Also got a blutooth OBDII scanner to use with "Tourque" app for my fone..can't wait till that gets here

cleenrob

Got the hesco t stat housing and robert shaw thermistat pit on today along with a coolant flush

I'm going to wait for a while on the flowkooler pump for a little while.

cleenrob

Got the hesco t stat housing and robert shaw thermistat pit on today along with a coolant flush

I'm going to wait for a while on the flowkooler pump for a little while.

cleenrob

Also pit on my negitive batt cables amd wired a switch to my taurus fan I I can switch it on when ever I so choose. I tapped into the cigerette lighter for a 12 v switched power source ( so it won't stay on when I'm not in the jeep)

I thin ill eventually wire in a plug harness for all the switches I put in there so I can un plug the switch panel

cleenrob

cleenrob

im also trying to find a solution to my temp probe for the fan controller. i feel like im not getting an accurate reading with placed loosely in the radiator.

so im trying to find a coolant sensor that will play nice with the fan controllor that i can place in the upper heater hose for a more accurate reading so the fan will kick on right when it needs to.

my plans as of now:
-extended brake lines
-29 spline c8.25 build/install
-trans cooler
-batt. cables and 136 amp alt.
-timken hubs/ new u joints
-junk yard rear bumper
-bedline some stuff
-flowkooler pump(?)
-new headliner
-6.5'' speakers all around
-SYE
-rebuild drive shafts
-regear
-ported cylinder head
-99 intake
-stroker someday

cleenrob

re adjusted my temp setting on my taurus fan controller tonite. i had it set too low and the high fan was running a lot

caldwell_sean

Here is a good video about porting 4.0 heads. This is how I did mine .


http://www.powerblocktv.com/episodes...ker-reassembly