Pre-Runner Build
#1
Senior Member
Thread Starter
Join Date: Dec 2009
Location: Fort Lauderdale
Posts: 642
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
Pre-Runner Build
I am building a Pre-runner for my little brother - in law. This is a 1996 2WD XJ 4DR AUTO. It's also going to be some free advertising for where i work since he lives on the other side of the state. so any input/suggestions would be greatly appreciated.
http://www.facebook.com/Morris4x4Cen...d=128584860528
http://www.facebook.com/Morris4x4Cen...d=128584860528
#3
#4
Senior Member
Thread Starter
Join Date: Dec 2009
Location: Fort Lauderdale
Posts: 642
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
it is just a few tiny holes. im only going to fill them in it looks worse in the pics than it really is. And yes the 4.5" kit will allow him to run some narrow 33's with minor trimming. whats wrong with doing that?
#5
because bondo doesnt stop rust and if the holes are rotted all the way through, the second bondo gets wet it swells up and falls apart and makes more rust
and i dont see how a basic 4.5'' kit makes it a 'pre runner'
look up what a pre runner is
a 6.5'' long arm kit, coilovers with remote rez's and a full roll cage and full skids would be more like a pre-runner
#6
because bondo doesnt stop rust and if the holes are rotted all the way through, the second bondo gets wet it swells up and falls apart and makes more rust
and i dont see how a basic 4.5'' kit makes it a 'pre runner'
look up what a pre runner is
a 6.5'' long arm kit, coilovers with remote rez's and a full roll cage and full skids would be more like a pre-runner
and i dont see how a basic 4.5'' kit makes it a 'pre runner'
look up what a pre runner is
a 6.5'' long arm kit, coilovers with remote rez's and a full roll cage and full skids would be more like a pre-runner
#7
because its sealed under 3/16'' of paint, and if its used over holes be prepared to be looking for another body shop and another paint job
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Dec 2009
Location: Fort Lauderdale
Posts: 642
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
exactly.
And we are in Florida bro, even if he had the money for long arms and coilovers he wouldnt need it. besides it is really more to look good than anything but still capable so he can wheel a little. so i gues we can call it a "wanna be pre-runner" hahaha
#9
I'm sorry but your logic fails. Its in the FLOOR PAN. HELLO! If he uses bondo and does it right. meaning that he gets all the rust off beforehand. then uses bondo, sands it flush(doesn't have to look good cause it'll be under carpet) and uses a can of rubber undercoating on the bottom and some good rattle can paint on the top he'll be fine.
#10
lifted cherokee...
i dont see the resemblance
#11
#12
well if its called a pre runner build it should be built into a pre runner.....
if i called my jeep a rock crawler build and lowered it and put 20''s on it i would get the same responce and that is actually prtetty much what youre doing
if i called my jeep a rock crawler build and lowered it and put 20''s on it i would get the same responce and that is actually prtetty much what youre doing
#14
Senior Member
Thread Starter
Join Date: Dec 2009
Location: Fort Lauderdale
Posts: 642
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
Maybe since it is called a pre runner build, it just might be...... maybe i dunno...., a pre runner when it's done! I did JUST start getting the cash flow for this build. Oh and remember a 17 year old junior in high school who works a Publix (grocery store for those of you who aren't fortunate enough to know the greatness that is) part time is paying for this $150 bucks at a time.
#15
Here's a good course of action for you to take:
Read this two threads:
http://www.race-dezert.com/forum/showthread.php?t=4123
http://www.performancetrucks.net/for...d.php?t=426424
Pull your head out of your rear end.
And stay away from Cherokee Forum till you can play nice.
X2 ignore the haters
Last edited by ZachsXJ; 12-30-2009 at 09:11 PM.