My 87 comanche 2wd.. You can guess what i'm doing :D
#1
CF Veteran
Thread Starter
Join Date: Jun 2009
Location: Michigan
Posts: 2,131
Received 290 Likes
on
239 Posts
Year: 1987 MJ, 1998 XJ, 1973 J2000, 89 waggy
Model: Comanche (MJ)
Engine: 4.0L H.O
My 87 comanche 2wd.. You can guess what i'm doing :D
payed $500 for it, i'm the 2nd owner now..hahaha
how it sits now in my garage
8.5" and 33" BFG mud terrains, long-arms are soon coming
i have swapped out the rear axle (stock dana 35) for a chrysler 8.25 from a 98, went leaf over axle and i've swapped out the tranny and installed a 242 t-case..... swapped steering columns out, bucket seats, center counsel, custom front bumper, and like i said, working on fabbing long arms and install
how it sits now in my garage
8.5" and 33" BFG mud terrains, long-arms are soon coming
i have swapped out the rear axle (stock dana 35) for a chrysler 8.25 from a 98, went leaf over axle and i've swapped out the tranny and installed a 242 t-case..... swapped steering columns out, bucket seats, center counsel, custom front bumper, and like i said, working on fabbing long arms and install
Last edited by That Jeep Guy XJMJ; 06-28-2009 at 11:19 PM.
The following 2 users liked this post by That Jeep Guy XJMJ:
Carlos Manuel Davis (06-07-2020),
Sandcast (11-02-2022)
#5
CF Veteran
Thread Starter
Join Date: Jun 2009
Location: Michigan
Posts: 2,131
Received 290 Likes
on
239 Posts
Year: 1987 MJ, 1998 XJ, 1973 J2000, 89 waggy
Model: Comanche (MJ)
Engine: 4.0L H.O
138k on original 4.0 I6 bullet proof hahah... they're deffinitely fun to look at...and they're even better to drive and see some reactions from other cherokee drivers
#7
CF Veteran
Thread Starter
Join Date: Jun 2009
Location: Michigan
Posts: 2,131
Received 290 Likes
on
239 Posts
Year: 1987 MJ, 1998 XJ, 1973 J2000, 89 waggy
Model: Comanche (MJ)
Engine: 4.0L H.O
wow its been sometime since i've updated this build thread....
so here's the cliff noted version of this novel build
re-did my lift up front... went with some rustys 9.5" lift coils with a pair of 2" spacers and now long armed and then shackled the rear end so its now sitting on 10" of lift
also swapped my axles out for a dana 30 front with the larger shafts and 4.10 gears and then rear is now a ford 8.8 with 4.10 gears and a LSD along with disc brakes
also picked up a set of 36" Iroks. got an awesome deal
and so the wheeling began
also added in a roll cage and some other goodies... CB, lights, flowmaster muffler with 2.5" exhaust out the back, as you could see in the last picture there are some big fender flares on the front now (garden flares... look em up in the fab section) now i'm working on finishing the rear set
so here's the cliff noted version of this novel build
re-did my lift up front... went with some rustys 9.5" lift coils with a pair of 2" spacers and now long armed and then shackled the rear end so its now sitting on 10" of lift
also swapped my axles out for a dana 30 front with the larger shafts and 4.10 gears and then rear is now a ford 8.8 with 4.10 gears and a LSD along with disc brakes
also picked up a set of 36" Iroks. got an awesome deal
and so the wheeling began
also added in a roll cage and some other goodies... CB, lights, flowmaster muffler with 2.5" exhaust out the back, as you could see in the last picture there are some big fender flares on the front now (garden flares... look em up in the fab section) now i'm working on finishing the rear set
The following users liked this post:
Carlos Manuel Davis (06-07-2020)
Trending Topics
#11
CF Veteran
Thread Starter
Join Date: Jun 2009
Location: Michigan
Posts: 2,131
Received 290 Likes
on
239 Posts
Year: 1987 MJ, 1998 XJ, 1973 J2000, 89 waggy
Model: Comanche (MJ)
Engine: 4.0L H.O
thx its actually the longest lasting vehicle i've owned now... lmao i've had it over 3 years now this summer. all the other jeeps i've owned have either broken down to crap or i've sold em to move on...
i'm fairly happy with how its turned out so far.... In a few weeks i'm going to be doing a full 4.0 HO motor swap, (harness, motor, tranny, tcase, dashboard) everything basically from my 95 XJ DD is gonne be swapped into it.. along with possibly a new roll cage, maybe some paint, and I'll be putting one of my ARB Bull Bars on it , plus a few other mods that you guys will just have to wait to see..... so it will be put up in the garage yet Again!! ugh!!!
Jbetit i wasnt sure if i've asked ya but were planning on going to the Jeep Blessing this weekend? i'll have it out and about up there and then at Twisted Trails until Sunday beating on it lol
#12
Senior Member
Join Date: Feb 2010
Location: Alto, MI
Posts: 938
Likes: 0
Received 1 Like
on
1 Post
Year: 2002
Model: Grand Cherokee
Engine: 4.7
I want to, but I can't. I graduate college Friday, and right after graduation I am going to Ohio to celebrate my grandpa's 80th. Don't beat on it to hard! lol
#14
CF Veteran
Join Date: Dec 2010
Location: Spanish Fork, Utah
Posts: 2,366
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: Renix 4.0L
Yeah, usually stuff with that much lift doesn't look too good. But yours is bad ***. Your tires back up your lift. Its sweet.
#15
CF Veteran
Thread Starter
Join Date: Jun 2009
Location: Michigan
Posts: 2,131
Received 290 Likes
on
239 Posts
Year: 1987 MJ, 1998 XJ, 1973 J2000, 89 waggy
Model: Comanche (MJ)
Engine: 4.0L H.O
ok... so i've officially started my drivetrain swap/ Update build this afternoon
mmmmm a familiar looking shot Kinda sad this thing has only been out and about for 5 months now and its back into the garage for more work....
doesnt look like a whole lot but all i need to do is pull my driveshafts, crossmember, and unbolt the motor mounts and its basically ready to be pulled
i even have a bad motor mount already hahaha i never even realized it. maybe a pic l8r on.....
mmmmm a familiar looking shot Kinda sad this thing has only been out and about for 5 months now and its back into the garage for more work....
doesnt look like a whole lot but all i need to do is pull my driveshafts, crossmember, and unbolt the motor mounts and its basically ready to be pulled
i even have a bad motor mount already hahaha i never even realized it. maybe a pic l8r on.....
The following users liked this post:
Carlos Manuel Davis (06-07-2020)