All show and no go build
Thread Starter
CF Veteran
Joined: Nov 2011
Posts: 2,752
Likes: 0
From: Nashville
Year: 2001
Model: Cherokee
Engine: 4.0
Will do. I'm with you busted, been eye balling them since they posted them on the jcr site.
Once we get the little stuff done and get the truck off the lift I'll be posting more picks of the gear we just dropped in.
Once we get the little stuff done and get the truck off the lift I'll be posting more picks of the gear we just dropped in.
Thread Starter
CF Veteran
Joined: Nov 2011
Posts: 2,752
Likes: 0
From: Nashville
Year: 2001
Model: Cherokee
Engine: 4.0
Ran into some problems during the test fit of the sliders. So we're a little behind schedule but that's ok cause I just got my hands on some OR Fab Upper Quarter Panel Armor.
Merry Christmas to me.
Merry Christmas to me.
Senior Member
Joined: Oct 2011
Posts: 958
Likes: 0
Originally Posted by fritzthekatt
Ran into some problems during the test fit of the sliders. So we're a little behind schedule but that's ok cause I just got my hands on some OR Fab Upper Quarter Panel Armor.
Merry Christmas to me.
Merry Christmas to me.
Thread Starter
CF Veteran
Joined: Nov 2011
Posts: 2,752
Likes: 0
From: Nashville
Year: 2001
Model: Cherokee
Engine: 4.0
Following the install instructions the brackets that tie into the unibody didn't line up with pinch seam . They were off a good 1/2 inch. Called JCR and they said to install them in reverse of what the instructions say. 
This is how they lined up on the first test run. Will be attempting the "reverse" install later.
This is how they lined up on the first test run. Will be attempting the "reverse" install later.
Thread Starter
CF Veteran
Joined: Nov 2011
Posts: 2,752
Likes: 0
From: Nashville
Year: 2001
Model: Cherokee
Engine: 4.0
I'm sure they can only take so many variables into account but to not have the install clearly laid out is nonsense.
I'm going to reach out to nowhres and see if he had issues with his install.
I'm going to reach out to nowhres and see if he had issues with his install.
Thread Starter
CF Veteran
Joined: Nov 2011
Posts: 2,752
Likes: 0
From: Nashville
Year: 2001
Model: Cherokee
Engine: 4.0
Installing the "correct" way has led to a huge gap. 
Hopefully a call to JCR Monday solves this...
Hopefully a call to JCR Monday solves this...
Last edited by fritzthekatt; Nov 15, 2013 at 09:07 AM.
CF Veteran
Joined: May 2011
Posts: 2,516
Likes: 4
From: va
Year: 1996
Model: Cherokee
Engine: i-6 4.0
Thread Starter
CF Veteran
Joined: Nov 2011
Posts: 2,752
Likes: 0
From: Nashville
Year: 2001
Model: Cherokee
Engine: 4.0
Spent most of the day going back and forth with JCR. Tried a couple fixes but we are pretty sure the driver side slider has some warp in it. Especially after the passenger side mocked up perfect. They've been helpful so we'll see if I can get them to send a replacement
It's a little hard to tell in the shot but this is the passenger side mock up.
It's a little hard to tell in the shot but this is the passenger side mock up.
CF Veteran
Joined: Nov 2010
Posts: 5,151
Likes: 0
From: glen burnie md
Year: 2000
Model: Cherokee
CF Veteran
Joined: May 2011
Posts: 2,516
Likes: 4
From: va
Year: 1996
Model: Cherokee
Engine: i-6 4.0