88whitecomanche's 98 cherokee build

Subscribe
Dec 30, 2015 | 09:42 AM
  #76  
Quote: The rotor was glazed...but I had them recut and got new pads
I was trying to cheap out on parts but every time I'm ever doing anything cheap I end up spending more than I want to.
I know for future reference to get everything new...
I ran into the same issue with my old GTI, try to save money on some parts you end up breaking more and it costs twice as much. So happy I got rid of that pos. Glad to see the pads where the only carnage, it could have been much worse.
Reply 0
Jan 2, 2016 | 06:47 AM
  #77  
Finally got my quadratech rear cargo liner...
It's already saved me a bit of a mess from this New Years resolving a locker issue...

Name:  17D6E971-0855-474D-A17F-20AB265F2771_zpsrus1xr3s.jpg
Views: 123
Size:  239.3 KB


Reply 0
Jan 3, 2016 | 12:22 AM
  #78  
Subbed
Reply 0
Jan 4, 2016 | 07:27 PM
  #79  
Met up with freegdr for a Jy run and no luck with parts...
But got a side by side pic

Name:  F7111906-0DD5-4706-B72B-3EFFAC46596E_zpskodd6vaz.jpg
Views: 149
Size:  419.1 KB

Name:  D5EB4D53-FC0C-4F8E-9F5C-C43E557C2632_zpsidejwf3k.jpg
Views: 129
Size:  215.8 KB

And noticed I was getting a lot of vibration up front...looked at my pinion and it's not good...which I don't understand because I put 4.5" coils up front the lowers are at 16.5" and the uppers are at 15"...
I'm going to have to adjust them again...or at least the uppers for sure...
Cell phone angle finder showed it at 4 degrees and read online that it should be at least from 6-8 degrees...
So I took off my front driveshaft until I can get it all dialed up....

Here's a pic of my pinion angle you can tell it's off...

Name:  24342459-3484-49AB-B6AF-252659276259_zpsqhchpcxp.jpg
Views: 120
Size:  222.1 KB


Reply 0
Jan 7, 2016 | 09:45 AM
  #80  
Any idea on the lift/tire specs on that 2 door? Best looking 2 door I've seen in a long time
Reply 0
Jan 7, 2016 | 11:49 AM
  #81  
Quote: Any idea on the lift/tire specs on that 2 door? Best looking 2 door I've seen in a long time
13" in the front 11" in the back 38" groundhawgs
Reply 0
Feb 5, 2016 | 07:05 AM
  #82  
Got-To Love it. Just went though your thread and SUB-It
Reply 0
Feb 11, 2016 | 11:41 AM
  #83  
Picked up a spare 29 spline 4.10 8.25 from a 99 2 door from the Jy...
Might go back to grab the panels and window regulators...

Name:  0418F4BF-59DD-47A2-86AB-DC1CB81495FB_zpsj8cgq4b7.jpg
Views: 126
Size:  198.3 KB

Name:  CDC87290-854B-4B5D-8DEE-8F55B58210B7_zpspy7vuiz2.jpg
Views: 118
Size:  231.4 KB

Name:  133816BE-8DB0-4C70-9FF4-6773D768467B_zpsu5goqjqu.jpg
Views: 128
Size:  206.9 KB

This 2 door was clean...besides a dent in the drivers door and a busted driver side seat bracket...


Reply 0
Feb 11, 2016 | 12:05 PM
  #84  
Super jealous of the 29 spline 4.10 8.25! I just told my wife the other day that if I find an XJ with stock 4.10 29 spline 8.25 rear I'd be ripping off both axles and taking them! lol. What did that rear end set you back if you don't mind me asking?
Reply 0
Feb 11, 2016 | 12:23 PM
  #85  
Nice find on the axle!
Reply 0
Feb 11, 2016 | 12:34 PM
  #86  
Quote: Super jealous of the 29 spline 4.10 8.25! I just told my wife the other day that if I find an XJ with stock 4.10 29 spline 8.25 rear I'd be ripping off both axles and taking them! lol. What did that rear end set you back if you don't mind me asking?
My first one was $210...
This one cost ran me $154....
Considering the cost to regear I'll take it any day of the week
Reply 0
Feb 11, 2016 | 12:35 PM
  #87  
Quote: Nice find on the axle!
Thanks...I've search for a few years now for this specific axle and in less than a few months I find 2
Reply 0
Feb 11, 2016 | 12:38 PM
  #88  
Quote: My first one was $210...
This one cost ran me $154....
Considering the cost to regear I'll take it any day of the week
Damn, that is great! Yeah I'd spend that much for an axle without hesitation haha. At that point I'd just rebuild the entire axle outside the Jeep since I'm already using a 3.55 C8.25 in it now. Disc brakes, locker, re paint, etc...


Looks like I need a trip to the JY
Reply 0
Feb 11, 2016 | 08:59 PM
  #89  
dude... cherokee coming out awesome, mad jealous here in texas lol

yo when did you put in a snorkel?
Reply 0
Feb 11, 2016 | 09:33 PM
  #90  
Quote: Damn, that is great! Yeah I'd spend that much for an axle without hesitation haha. At that point I'd just rebuild the entire axle outside the Jeep since I'm already using a 3.55 C8.25 in it now. Disc brakes, locker, re paint, etc...


Looks like I need a trip to the JY
I might really consider disk brakes...but I've never had a problem with drum brakes...
Do you have a write up on the brake swap?

Quote: dude... cherokee coming out awesome, mad jealous here in texas lol

yo when did you put in a snorkel?
Lol I didn't...it came with the xj when I traded it...
I'm not a big fan of it...I get comments ALL the time for it to...
How's your xj coming along?
Reply 0