That a very good decision.

What all comes in a gear set up kit?

 

Here's what I bought.
Everything but the gears basically.

 

That seems like a pretty good price to me. But then again I bought all my parts individually for my Chrysler 8.25

 

55% off ??
Reg price is a hell of a markup!

 

Yeah I was going to pick some up during this sale too, but they raised their prices a fair amount it seems

 

Saw that too. Standard retail trick, you think you're getting a great deal when in reality you're paying almost just as much as full price with a standard discount.

 

Yeah there is a big thread on pirate4x4 on them raising the prices before announcing that sale, but it ended up being about 10% off and free shipping, so I went for it.

 

I've still been chasing a vibration. I pulled the diff cover back off and checked the gear wear pattern. It looked weird, so I put some photos up on pirate and they thought the gears were toast, but also someone suggested it was the pinion angle that was causing the vibration.
Going to order some gears for it and do it all at one time.
I ordered some 2.5 degree wedges to get the pinion angle right and see if that fixes the vibration.

Also ordered a fuel tank skid plate.

No mention if my tires have shipped yet. the wait continues.

 

Damn thats along wait for shipping. I am not built with the patience for that.
Sweet rig though.

 

I've still been chasing the vibration. Not 100% sure it is the rear end, so I don't want to go pulling it apart and spending $250 on another gear set. It kind of feels like it could be in the transfer case too.
I've put pinion shims to fix the pinion angle and balanced the rear tires. No fix with either of those.
I'm really trying everything I can think of before having to go to gears. I really hate setting up gears. LOL

I got a gas tank skid plate for my birthday though.


Iron Rock Offroad.
Fit well, looks good.



Took a drive yesterday morning to feel out the vibration and see if I could pin point it with different scenarios. No luck.
Had to go offroad a little bit while I was out.

 

Any close ups on that CB antenna in the rear? It's very interesting. Is it using the factory windshield wiper stud? It'd be funny if you could rotate the antenna like a wiper...lol. I never use my rear wiper and it looks pretty cool. The Jeep looks great, keep up the good work.

 

Yeah, I'll get a photo of it and post it up.
It is a firestick and yes it is in place of the rear wiper.
I thought it was a great idea. The base was there when I purchased the Jeep. I had to add the antenna.
All tuned and ready to go.

Thanks man

 

Nice Jeep! That is one very cleanly built 3/4 Ton XJ.

You've got some awesome wheeling in your backyard it seems.

 

Thank you sir. I got a nice one. Trying to fix some issues and taylor it to my needs.

Aetna Mountain used to be the place to go around here until all the fighting about the road and land use started happening.
You can still go up there, but there is a possibility of being hassled, so I just stay away.
You hit up the two largest places while you were here though.

 

I've been slacking on the updates. Mainly because the work has been very slow.

Things I've done -
New A/C compressor
New gears, bearings for the rear end
New beadlock/tire setup
New Ball Joints
New brake pads for the front (one was cracked)

I've been waiting for the wheel/tire setup for a couple of months, so the jeep has just been sitting.

The tires finally came in June 25th after ordering them February 14th...



Meaty!



Good help is hard to find!



Driver side Ball Joints were bad, so I had to take care of that.







Going back together.




Found a cracked brake pad while I was in there.




Back together



A shot while pulling Vacuum on the A/C system



Rear end out. I had totally decided to set the gears up myself. As I was refreshing my memory on the set up, I decided that I would let someone do it that does it every day.
Don't regret sending it for someone else to do.



Matching numbers on the new gears. :giggity:



Back under!



I measured the rear quarters, designed some 1/8" plates to go on them and had them burned out at work. Come to find out, whoever made the modifications to the rear quarters warped them pretty good.
Haven't decided what to do about that yet.
Here are the pieces that I did.



The wheels were ordered through a friend that is a dealer for FUEL wheels. I didn't even know they made beadlocks until I was randomly searching for them online.
He hooked me up, but it was a long wait. That's ok. I can wait.
They arrived Friday. I test fitted them and immediately took them to powdercoat.







The powdercoater called yesterday while I was at work telling me that they were finished. I took off early to get my daughter, so that was a great opportunity to go get them.





I went ahead and put one together. (took 45 minutes)











I won't be able to get them balanced until Friday, so I'll put one together tonight, then tomorrow and then Friday morning before getting them balanced.

That's where I am at the moment.

So yeah... It's been a while. Sorry for the long wait.