windshield replacement
#2
CF Veteran
I had the same Q & found that it is super hard to get the old windshield out without breaking it (nice to know if you want one from a JY).
Really cheap to get one put in professionally, so I hear. I've yet to make any calls to a glass shop.
Really cheap to get one put in professionally, so I hear. I've yet to make any calls to a glass shop.
#3
CF Veteran
Join Date: Jun 2011
Location: Louisville,KY
Posts: 8,014
Likes: 0
Received 14 Likes
on
14 Posts
Model: Cherokee
I have tried cutting one out a few times out of 5 only one i didn't break its harder then it looks.I would spend the money and pay a pro to do it.If you have full coverage on your jeep glass should be covered on your insurance.
#4
CF Veteran
Join Date: Nov 2011
Location: City of Trees, CA
Posts: 7,387
Likes: 0
Received 10 Likes
on
9 Posts
Year: 93 2 door
Model: Cherokee
Engine: 4.0
PAIN IN THE ***! just flow someone a couple bucks to do it for you or have it professionally done. I couldn't get mine out. and I was using a sawzall
#6
CF Veteran
Get a buddy. You hold a piece of wire on the inside of your Jeep, while your buddy holds the other end on the outside of the cabin. The wire has to be thin enough to cut the rubber but strong enough to not break (think Piano wire). Take your time. It helps to go ahead of the wire with a heatgun to get the rubber seal hot.
Scrape off the old stuff with a blade and heatgun, pick up some silicone sealant, and glue it in place. Use tape to hold and align it in place.
Scrape off the old stuff with a blade and heatgun, pick up some silicone sealant, and glue it in place. Use tape to hold and align it in place.
Trending Topics
#8
Member
Join Date: Sep 2013
Location: Marshfield, Missouri
Posts: 147
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
get a rope about 4 foot long, you want a 1/4 inch cotton rope. soak it in soapy water(really soapy!) feed it through from either the outside or inside. you need someone to hold one end and you hold the other work it around the seal....done!
#9
CF Veteran
Join Date: Sep 2011
Location: Riviera, Texas
Posts: 4,172
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1998 Sport
Model: Cherokee
Engine: 4.0
It really not to hard if you have someone to give you a hand. But if you don't call around a few glass shops. Here in South Texas there are a lot of auto glass shops and they charge around $150 for a new windshield including installation. I had my son's car windshield replaced a couple of weeks ago and my ex girlfriends done done about a year ago. For me $150 was worth not to have to deal with having a mess on my hands if the glass shattered.
#10
CF Veteran
Join Date: Jul 2012
Location: SD
Posts: 1,395
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
Years ago I helped my friend replace the windshield in my '67 Belvedere. I know that it's not anything I'll ever attempt by myself. For what the glass shops charge to do it, it's just not worth the risk and frustration of doing it myself.
#11
CF Veteran
Join Date: Sep 2009
Location: ☼ Blackhole Sun
Posts: 8,567
Likes: 0
Received 18 Likes
on
16 Posts
Year: My Jeep is a GMC
Get a buddy. You hold a piece of wire on the inside of your Jeep, while your buddy holds the other end on the outside of the cabin. The wire has to be thin enough to cut the rubber but strong enough to not break (think Piano wire). Take your time. It helps to go ahead of the wire with a heatgun to get the rubber seal hot.
Scrape off the old stuff with a blade and heatgun, pick up some silicone sealant, and glue it in place. Use tape to hold and align it in place.
Scrape off the old stuff with a blade and heatgun, pick up some silicone sealant, and glue it in place. Use tape to hold and align it in place.
#12
CF Veteran
Join Date: Nov 2010
Location: some small town oregon
Posts: 15,581
Likes: 0
Received 8 Likes
on
8 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
X2. Windshields are held in by a urethane sealant and adhesive. The "rubber seal" I keep seeing people mention is only on the rear side windows and hatch. I've done one by myself.... it was horrible. I will pay a guy to do it with the correct stuff.
#13
Seasoned Member
Join Date: Jul 2013
Location: Spokane Valley, WA
Posts: 432
Likes: 0
Received 1 Like
on
1 Post
Year: 1989
Model: Cherokee
Engine: 4.0
Get a buddy. You hold a piece of wire on the inside of your Jeep, while your buddy holds the other end on the outside of the cabin. The wire has to be thin enough to cut the rubber but strong enough to not break (think Piano wire). Take your time. It helps to go ahead of the wire with a heatgun to get the rubber seal hot.
Scrape off the old stuff with a blade and heatgun, pick up some silicone sealant, and glue it in place. Use tape to hold and align it in place.
Scrape off the old stuff with a blade and heatgun, pick up some silicone sealant, and glue it in place. Use tape to hold and align it in place.
Number one even thin wire can chip the edges of the glass which leads to cracks.
Number two silicone sealant is not strong enough or even legal to use in glass replacement. ONLY USE AN APPROVED URETHANE SEALANT that is made for glass.
I've replaced hundreds of windshields and trust me cutting out a used one with the proper tools is tough at best. They then need to be cleaned and prep'd properly as well to ensure the seal right and stay in place. I had Safelite quote mine about a month ago and they cam in at $188.00. Pay a pro to do it cause in a worst case scenario the glass is the last thing that will keep you in your jeep when the poop hit's the fan. Silicone will put your *** on the road!
Black89
#14
Seasoned Member
Join Date: Sep 2011
Location: Oregon
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: Inline Six
Not to kill the subject, but I would have to agree with having it done professionally. I am a big, "Do It Yourselfer" and did try to get a windshield from a junk yard. My dad and I went through at least 3 windshields. One of which we almost had, but ended up cracking at the end. One thing I noticed is alot of the windshields in the junk yard have small chips in them. Long story short, $300 is one of those jobs where its worth having done. It will save you time and frustration.
#15
Aaron Autoglass in chicago (and other towns in IL)
Will replace it for $100, if they have any used glass in stock.
Yup $100 thats parts and labor.
(again if they have used glass avaliable and in stock.)
Will replace it for $100, if they have any used glass in stock.
Yup $100 thats parts and labor.
(again if they have used glass avaliable and in stock.)