Removing door check pin
#1
Newbie
Thread Starter
Join Date: May 2012
Location: Harrisonburg, VA
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Removing door check pin
Trying to replace the door check pin and bracket. For the life of me I cannot get the old pin out. I'm just trying to hammer it out from the bottom. I've hammered on it so much that the bottom of the pin is a little deformed from me pounding on it, but it's not coming up at all. Anyone have any ideas or advice?
#2
CF Veteran
Join Date: Jul 2009
Location: Keesler AFB, MS
Posts: 1,640
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998 XJ
Model: Cherokee
Engine: 4.0L
Trying to replace the door check pin and bracket. For the life of me I cannot get the old pin out. I'm just trying to hammer it out from the bottom. I've hammered on it so much that the bottom of the pin is a little deformed from me pounding on it, but it's not coming up at all. Anyone have any ideas or advice?
#4
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 17 Likes
on
17 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
On anything like that you might want to "back up" , the bracket when you smack the pin. (with authority) A "crisp" shot. Heat can really help. Even slowly pouring boiling water on it might get it hot enough to make a difference. Btw, I'm not positive, but I believe that assembly needs to go in, to get it out. Not sure there.
#6
Newbie
Thread Starter
Join Date: May 2012
Location: Harrisonburg, VA
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Thanks for the replies and advice. Upon taking a close look, rather than just pounding away, it appears that the pin has been cracked, broken, or bent. There is an uneven lip on the pin, below the arm, that must be keeping it from coming up through the holes. If I stick a flat head screwdriver in there, I can feel that the pin has an edge and isn't smooth. What now? Thanks in advance for any ideas.
#7
I used a Phillips screw driver and set it into the bottom of the pin and hammer the screw driver.
Your alternative is to unbolt the entire assembly and remove. This would require removing the door panel and unbolting the door check and the pin hinge from the frame.
Your alternative is to unbolt the entire assembly and remove. This would require removing the door panel and unbolting the door check and the pin hinge from the frame.
Trending Topics
#9
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 17 Likes
on
17 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
X2, Those little cutting wheels for a dremmel are no joke. You can cut allot of steel, or a 3/8 bolt with just one or two. I got 50 on ebay..I forget $10 or 15 bucks. Don't you need to change the whole thing though? I had no luck finding one at my local JY, but I might consider just swapping the whole works...guess you might still need to cut the "bar", though. Again, I'm not sure.
Thread
Thread Starter
Forum
Replies
Last Post
investinwaffles
Modified XJ Cherokee Tech
11
05-18-2021 12:02 PM
hpwrestler220
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
5
03-03-2017 01:13 AM
SlickXJ
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
4
08-29-2015 09:28 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)