real main seal issue please help
#1
Newbie
Thread Starter
Join Date: Sep 2015
Location: alaska
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
real main seal issue please help
I removed those 2 bolts but its stuck on there. is there something else i need to unbolt after taking my pan off to change the seal?
I searched around and no one seems to be having this issue
#4
Member
Join Date: Jul 2015
Location: Sugar Land, TEXAS
Posts: 232
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0 165,00 Miles
The bearing cap is held in place with dowels. To remove the cap, unscrew the main bearing cap bolts and pull them clear of the block but leave them in the bearing cap. Pinch the two bolts together and rock in the "east-west" direction while pulling down. It'll break free after a few seconds of this.
Or, gentle tapping and I have heard some say you can loosen a few more of them down the line which they say helps sometimes.
Or, gentle tapping and I have heard some say you can loosen a few more of them down the line which they say helps sometimes.
#5
Newbie
Thread Starter
Join Date: Sep 2015
Location: alaska
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
The two bolts in the photo believe they were 21mm the bottom half of the seal wont pop out the last person must have used a lot of rtv or something
Trending Topics
#8
Newbie
Thread Starter
Join Date: Sep 2015
Location: alaska
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
I was watching that video and the one by bleepnjeep while i was doing it, mine is a little different i didnt see a gurtle i had to remove just popped the pan and unbolted the rear cap
#9
Newbie
Thread Starter
Join Date: Sep 2015
Location: alaska
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
Its a bad pic but i dont see a long gurtle i need to remove, so i just kept goin thinkin maybe now i missed something thats why it wont come off, my oil pan took 2 pry bars to get off it was super crusted on there
#10
Member
Join Date: Jul 2015
Location: Sugar Land, TEXAS
Posts: 232
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0 165,00 Miles
I believe only the 99-2001 had the girdle. There is no girdle in your picture. Was there a lot of sludge in the pan? If so you are going to have to work that bearing off. Put a small block of wood on it and tap harder or a nylon hammer. Maybe a brass punch to lightly work around it. It WILL come off. HEAT might help if nothing else does.
Last edited by Sandyman; 01-10-2016 at 09:07 PM.
#11
Newbie
Thread Starter
Join Date: Sep 2015
Location: alaska
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
Ok i didnt know.. all the videos i watched i seen a girdle so i was just a lil thrown off and yeah there was some crusty stuff by my drain hole after i got my pan off, ill be switching to mobile 1 synthetic after this
#13
Newbie
Thread Starter
Join Date: Sep 2015
Location: alaska
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
Dont know whats goin on, maybe my jeep just hates me, but ive taken 3 caps off and the upper seal just wont come out. Ive been bangin on it with a punch for an hour any tips?