I want to convert

Subscribe
Jul 11, 2015 | 06:24 AM
  #16  
Find a wrecked xj or one with a blown motor buy the whole thing and use all the parts you can off it and scrap the rest.
Reply 0
Jul 11, 2015 | 11:39 AM
  #17  
Part time lights work on XJs??

No electrical required lol
Reply 0
Jul 11, 2015 | 11:53 AM
  #18  
What light?
where?
I just look at where the lever is.

At first I thought this thread was gonna be
Reply 0
Jul 11, 2015 | 08:00 PM
  #19  
So the stock ecu and tcu will work ?
Reply 0
Jul 12, 2015 | 07:50 AM
  #20  
Yes... Lol

Jeeps are not that complicated. The difference between 2WD and 4WD transmissions is the output shaft and a tail extension housing to support it.
Reply 0
Jul 12, 2015 | 11:23 PM
  #21  
Subbed, because I'm still toying with the idea of doing this to mine.

Also, I think we should start a '96 XJ club/support group.
Reply 0
Jul 13, 2015 | 06:53 PM
  #22  
I've got a line on a 94 it's 4x4 will this stuff work for me ?
And if not I have a Chrysler 8.25 what front axles will work for me ?
Reply 0
Jul 13, 2015 | 09:27 PM
  #23  
Yep, should.

What you need to verify is:

- Transmission is compatible. See here for the AW4: http://www.naxja.org/forum/showthread.php?t=1053970
- Gear ratios of axles are the same (all 4.0L AW4s shipped with 3.55:1 post-1988)
- Drive shaft must be matched to the axle and year transfer case

So if this 1994 is a 4.0L AW4 XJ, the transmission will work with your 1996's TCU. It would have either a D35 or ****ty 27-spline C8.25 with 3.55:1 ratio. If it has a D35 and you want to use your existing C8.25, you'll need to lift your XJ, or the DS will be too long and bottom out the slip yoke. Otherwise you must stick with the D35.
Reply 0
Jul 19, 2015 | 11:11 PM
  #24  
I appreciate all the responses . My xj is lifted 3" on 31s. How do I find out the gear ratio of my rear end ? And the 94 turned out to be a bust . Will keep this thread updated and post again soon when I find another suitable donor .
Reply 0
Jul 19, 2015 | 11:57 PM
  #25  
^
If you pull the cover (might as well change the stink lube anyway) it's stamped on the ring gear.
Reply 0
Jul 21, 2015 | 10:18 PM
  #26  
Going to pick up everything tomorrow off a 96 . Guys selling me the tranny tcase linkage drive shafts and front axle for 330 is that a good deal . Anything else I need ? And what maintenance should I do to these parts prior to install ?
Reply 0
Jul 22, 2015 | 12:44 AM
  #27  
Quote: Going to pick up everything tomorrow off a 96 . Guys selling me the tranny tcase linkage drive shafts and front axle for 330 is that a good deal . Anything else I need ? And what maintenance should I do to these parts prior to install ?
Ujoints, ball joints, axle seals,
Reply 0
Jul 22, 2015 | 07:42 AM
  #28  
And the front brakes if the axle has sit out in the weather for a while.
Reply 0
Subscribe
Currently Active Users (1)