How to get trouble codes
#1
Newbie
Thread Starter
Join Date: Jan 2012
Location: Jacksonville, AL
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L inline 6
How to get trouble codes
I dont know how to get trouble codes for my 1989 jeep cherokee 4.0L. how do i get the codes?
#6
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 17 Likes
on
17 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
You hear the pump run for a sec or two when you turn on the Ign? Key it on and off a few times, few secs on each time. Then try it.
When you look around the forum, remember last year of Renix was 90
https://www.cherokeeforum.com/f51/he...ix-links-1397/
http://www.greatlakesxj.com/tech.html < I think the 90 is close enough
When you look around the forum, remember last year of Renix was 90
https://www.cherokeeforum.com/f51/he...ix-links-1397/
http://www.greatlakesxj.com/tech.html < I think the 90 is close enough
Last edited by DFlintstone; 01-10-2012 at 12:54 AM.
#7
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,863
Received 1,524 Likes
on
1,236 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
If you've got a multi-meter, test the CPS output.
Renix CPS Testing and Adjusting
Renix CPSs have to put out a strong enough signal to the ECU so that it will provide spark.
Most tests for the CPS suggest checking it for an ohms value. This is unreliable and can cause some wasted time and aggravation in your diagnosis of a no-start issue as the CPS will test good when in fact it is bad.
The problem with the ohms test is you can have the correct amount of resistance through the CPS but it isn’t generating enough voltage to trigger the ECU to provide spark.
Unplug the harness connector from the CPS. Using your voltmeter set on AC volts and probing both wires in the connector going to the CPS, crank the engine over. It won’t start with the CPS disconnected.
You should get a reading of .5 AC volts.
If you are down in the .35 AC volts range or lower on your meter reading, you can have intermittent crank/no-start conditions from your Renix Jeep. Some NEW CPSs (from the big box parts stores) have registered only .2 AC volts while reading the proper resistance!! That’s a definite no-start condition. Best to buy your CPS from Napa or the dealer.
Sometimes on a manual transmission equipped Renix Jeep there is an accumulation of debris on the tip of the CPS. It’s worn off clutch material and since the CPS is a magnet, the metal sticks to the tip of the CPS causing a reduced voltage signal. You MAY get by with cleaning the tip of the CPS off.
A little trick for increasing the output of your CPS is to drill out it’s mounting holes with the first drill bit that just won’t fit through the original holes. Then, when mounting it, hold the CPS down as close to the flywheel as you can while tightening the bolts.
Revised 11-29-2011
Renix CPS Testing and Adjusting
Renix CPSs have to put out a strong enough signal to the ECU so that it will provide spark.
Most tests for the CPS suggest checking it for an ohms value. This is unreliable and can cause some wasted time and aggravation in your diagnosis of a no-start issue as the CPS will test good when in fact it is bad.
The problem with the ohms test is you can have the correct amount of resistance through the CPS but it isn’t generating enough voltage to trigger the ECU to provide spark.
Unplug the harness connector from the CPS. Using your voltmeter set on AC volts and probing both wires in the connector going to the CPS, crank the engine over. It won’t start with the CPS disconnected.
You should get a reading of .5 AC volts.
If you are down in the .35 AC volts range or lower on your meter reading, you can have intermittent crank/no-start conditions from your Renix Jeep. Some NEW CPSs (from the big box parts stores) have registered only .2 AC volts while reading the proper resistance!! That’s a definite no-start condition. Best to buy your CPS from Napa or the dealer.
Sometimes on a manual transmission equipped Renix Jeep there is an accumulation of debris on the tip of the CPS. It’s worn off clutch material and since the CPS is a magnet, the metal sticks to the tip of the CPS causing a reduced voltage signal. You MAY get by with cleaning the tip of the CPS off.
A little trick for increasing the output of your CPS is to drill out it’s mounting holes with the first drill bit that just won’t fit through the original holes. Then, when mounting it, hold the CPS down as close to the flywheel as you can while tightening the bolts.
Revised 11-29-2011
Thread
Thread Starter
Forum
Replies
Last Post
sluger17
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
9
07-08-2023 07:08 AM
extrashaky
Other Vehicles. Other Jeep models & cars and trucks of other makes
17
06-17-2023 03:57 PM
tleed
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
3
10-04-2015 01:20 PM
mattsmith
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
4
10-02-2015 04:46 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)