Jeep Cherokee Forum
OEM Renix.
OEM Renix.
0 2016/06/25 21:29:47
Cover the terminals and reinstall.
Cover the terminals and reinstall.
0 2016/06/25 21:29:31
Found some Ox-Gard at Lowes, I believe.
Found some Ox-Gard at Lowes, I believe.
0 2016/06/25 21:29:25
Clean off the terminals on the coil.
Clean off the terminals on the coil.
0 2016/06/25 21:29:15
Vacuum out the crap, give the contacts a good brushing/cleaning and bend them back in so they make better contact.
Vacuum out the crap, give the contacts a good brushing/cleaning and bend them back in so they make better contact.
0 2016/06/25 21:29:07
Disconnect the cable to the distributor
Disconnect the cable to the distributor
0 2016/06/25 21:28:22
Reinstall and put it back on. I reused my blue Felpro gasket.
Reinstall and put it back on. I reused my blue Felpro gasket.
0 2016/06/25 21:11:00
Come over to you drill press and place a 1/2" hole in the snout on the side facing the firewall.
Come over to you drill press and place a 1/2" hole in the snout on the side facing the firewall.
0 2016/06/25 21:10:37
0 2016/06/25 21:10:30
0 2016/06/25 21:10:17
Go over to your home-made, treadmill powered (fully speed adjustable for metal and wood (and all free except the pillow blocks and pulleys!)) band saw and trim along the mark.
Go over to your home-made, treadmill powered (fully speed adjustable for metal and wood (and all free except the pillow blocks and pulleys!)) band saw and trim along the mark.
0 2016/06/25 21:10:04
Do the same on the second one.
Do the same on the second one.
0 2016/06/25 21:09:55
Measure 1 inch from the end of the snout and mark it
Measure 1 inch from the end of the snout and mark it
0 2016/06/25 21:09:43
Clean everything off.
Clean everything off.
0 2016/06/25 21:09:22
Pull the snouts off. I've previously cleaned the cover, but this time, those flimsy gaskets didn't survive. Tossed 'em.
Pull the snouts off. I've previously cleaned the cover, but this time, those flimsy gaskets didn't survive. Tossed 'em.
0 2016/06/25 21:09:10
0 2016/06/25 21:06:46
0 2016/06/25 20:47:18
This is the back of the chassis side of the connector.
This is the back of the chassis side of the connector.
0 2016/06/25 20:43:00
Take the screws out, disconnect the connector and remove the back covers. You need to be able to compare corresponding wires on either side of the connector and this gives you access to the front of the connector.
Take the screws out, disconnect the connector and remove the back covers. You need to be able to compare corresponding wires on either side of the connector and this gives you access to the front of the connector.
0 2016/06/25 20:42:53
0 2016/06/25 20:42:45
I had previously cleaned the connector, but you can see how long that lasted.
I had previously cleaned the connector, but you can see how long that lasted.
0 2016/06/25 20:42:38
The culprit.
The culprit.
0 2016/06/25 20:42:34
All done. Bundle it back up!
All done. Bundle it back up!
0 2016/06/25 20:42:06
Slide the heat shrink up and shrink it. 20 something more to go. Go slow and make sure you are connecting the correct wire pairs.
Slide the heat shrink up and shrink it. 20 something more to go. Go slow and make sure you are connecting the correct wire pairs.
0 2016/06/25 20:41:58
Clip them from the harness and solder all six together. Be sure to put the heat shrink on first.
Clip them from the harness and solder all six together. Be sure to put the heat shrink on first.
0 2016/06/25 20:41:52
0 2016/06/25 20:41:40
Co
Co
0 2016/06/25 20:41:31
These are the chassis side of the harness
These are the chassis side of the harness
0 2016/06/25 20:41:21
Solder the pair together.
Solder the pair together.
0 2016/06/25 20:41:14
These three are on the engine side of the harness
These three are on the engine side of the harness
0 2016/06/25 20:41:00
The infamous ground connectors.
The infamous ground connectors.
0 2016/06/25 20:40:54
Loosely attache the connector back together so you can see the wire pairs. As you clip the wires, only do one wire on each side and verify by testing continuity on the clipped wires. Strip the wires, slide a piece of heat shrink on one side.
Loosely attache the connector back together so you can see the wire pairs. As you clip the wires, only do one wire on each side and verify by testing continuity on the clipped wires. Strip the wires, slide a piece of heat shrink on one side.
0 2016/06/25 20:40:43
Let's buy a new one.
Let's buy a new one.
0 2016/06/19 16:33:56
The new radiator was from a newer year donor vehicle and the tranny oil line fittings didn't match.
The new radiator was from a newer year donor vehicle and the tranny oil line fittings didn't match.
0 2016/06/19 16:32:42
0 2016/06/19 16:31:55
0 2016/06/19 16:31:45
0 2016/06/19 16:25:54
Then, you put some man into it and it snaps off. In the crank. Not cool
Then, you put some man into it and it snaps off. In the crank. Not cool
0 2016/06/19 16:25:40
0 2016/06/19 16:25:07
The original bolt holding on the harmonic balancer was too short to get started to push the new balancer on, so off to Lowes to buy a longer one, to get it started.
The original bolt holding on the harmonic balancer was too short to get started to push the new balancer on, so off to Lowes to buy a longer one, to get it started.
0 2016/06/19 16:24:56