Jeep Cherokee Forum
Rear still open, bracing to come.
Rear still open, bracing to come.
0 2012/05/14 17:26:30
1st fit up
1st fit up
0 2012/05/14 17:26:30
Marking the front and rear crossovers to accept the rack base bars and side tubes.
Marking the front and rear crossovers to accept the rack base bars and side tubes.
0 2012/05/14 17:26:30
Laying out the stock roof crossovers
Laying out the stock roof crossovers
0 2012/05/14 17:26:30
Build the Peep somethin nice for long and loyal service
Build the Peep somethin nice for long and loyal service
0 2012/05/08 18:35:06
Bolt one end prior to moving on to next holes
Bolt one end prior to moving on to next holes
0 2012/05/08 18:35:06
Secure your work and back grind your bit webb to relieve chips
Secure your work and back grind your bit webb to relieve chips
0 2012/05/08 18:35:06
Drill base bars together for holes lineup
Drill base bars together for holes lineup
0 2012/05/08 18:31:06
Round to Angle end transitions
Round to Angle end transitions
0 2012/05/08 18:31:06
These will assemble at corners
These will assemble at corners
0 2012/05/08 18:31:06
Is this layout starting to look familiar
Is this layout starting to look familiar
0 2012/05/08 18:31:06
Assembly will be on top of stock rack crossovers
Assembly will be on top of stock rack crossovers
0 2012/05/08 18:31:06
1 inch Stainless Spacers plus M8-1.25 x 45mm When running blocks this completes the shock back to normal operating position and range.
1 inch Stainless Spacers plus M8-1.25 x 45mm When running blocks this completes the shock back to normal operating position and range.
0 2012/03/18 17:30:02
Sensatrac Standard and Load Assist Type, plus 80000 miles, 7" stroke (13 - 20 inch)
Sensatrac Standard and Load Assist Type, plus 80000 miles, 7" stroke (13 - 20 inch)
0 2012/03/18 17:30:02
Ive seen some bring it right up onto the axle, remember there is a lip seal inside the housing, watch the heat.
Ive seen some bring it right up onto the axle, remember there is a lip seal inside the housing, watch the heat.
0 2011/10/15 16:22:33
Nice extra clear under the axle
Nice extra clear under the axle
0 2011/10/15 16:22:33
That Monroe Sensitrac with Load Assist spring fits like a glove
That Monroe Sensitrac with Load Assist spring fits like a glove
0 2011/10/15 16:22:33
Shoot it with rust paint
Shoot it with rust paint
0 2011/10/15 16:22:33
Weld complete, even a little inside at top as torch will fit
Weld complete, even a little inside at top as torch will fit
0 2011/10/15 16:07:02
Tack in place
Tack in place
0 2011/10/15 16:07:02
Check your fit and sand bevel on edge to assist weld penatration
Check your fit and sand bevel on edge to assist weld penatration
0 2011/10/15 16:07:02
Trim back 1/2 to 5/8 inch
Trim back 1/2 to 5/8 inch
0 2011/10/15 16:07:02
Clean for welding, mark 1/2 way up, cut with zip disc.
Clean for welding, mark 1/2 way up, cut with zip disc.
0 2011/10/15 16:07:02
Recondition Done
Recondition Done
0 2014/04/12 17:15:14
Torque Spacer
Torque Spacer
0 2014/04/12 17:15:14
Parts On
Parts On
0 2014/04/12 17:15:14
Installed If you got it apart anyway, refresh it
Installed If you got it apart anyway, refresh it
0 2014/04/12 17:15:14
fixed 8Im happy with repair
fixed 8Im happy with repair
0 2014/04/12 17:15:14
fixed 9
fixed 9
0 2014/04/12 17:11:36
fixed 4 Some patience, a four foot bar, a three pound baby sledge.
fixed 4 Some patience, a four foot bar, a three pound baby sledge.
0 2014/04/12 17:11:36
fixed 2
fixed 2
0 2014/04/12 17:11:36
fixed 1 Almost fully persuaded.
fixed 1 Almost fully persuaded.
0 2014/04/12 17:11:36
its me or the tree
its me or the tree
0 2014/04/12 17:11:36
Whack a Deer 2
Whack a Deer 2
0 2014/04/12 17:08:19
Whack a Deer 3
Whack a Deer 3
1 2014/04/12 17:08:19
Whack a Deer
Whack a Deer
0 2014/04/12 17:08:19
Whack a Deer 1
Whack a Deer 1
0 2014/04/12 17:08:19
Deer Ouch
Deer Ouch
0 2014/04/12 17:08:19
Distraction
Distraction
0 2013/10/31 19:39:58
Nyala3
Nyala3
0 2013/10/31 19:39:58