Jeep Cherokee Forum
0 2025/11/27 19:22:56
0 2025/11/27 19:22:53
0 2025/11/27 19:22:51
0 2025/11/27 19:22:49
0 2024/11/24 18:18:25
0 2024/11/24 18:17:33
0 2024/06/02 13:42:49
0 2024/06/02 13:42:42
0 2024/06/02 01:25:02
0 2024/06/02 01:24:56
0 2024/06/02 01:24:48
0 2024/06/02 01:24:38
0 2024/05/08 11:10:44
0 2024/05/08 11:09:52
0 2024/05/08 11:09:45
0 2024/05/08 11:09:39
0 2024/05/08 11:09:33
0 2024/05/08 11:09:26
0 2024/05/08 11:09:19
0 2024/05/08 11:09:10
0 2023/12/06 23:16:13
0 2023/12/06 23:16:06
No plug wires from coolant reservoir to engine block. Cleaner IMO
No plug wires from coolant reservoir to engine block. Cleaner IMO
0 2023/12/06 23:16:00
0 2023/12/06 23:15:54
0 2023/12/06 23:15:49
Coil harness with wire loom routed behind dipstick tube. You can also see the flat bracket attached to the stud that holds the ignition capacitor (little black box).
Coil harness with wire loom routed behind dipstick tube. You can also see the flat bracket attached to the stud that holds the ignition capacitor (little black box).
0 2023/12/06 23:15:44
Nicely tucked away
Nicely tucked away
0 2023/12/06 23:15:38
Cut and fixed harness
Cut and fixed harness
0 2023/12/06 23:00:15
The trial and error harness
The trial and error harness
0 2023/12/06 23:00:09
Van coil plug that I used instead of the jumper plug
Van coil plug that I used instead of the jumper plug
0 2023/12/06 23:00:04
Extended wires. This end connectors to where the coil rail attached
Extended wires. This end connectors to where the coil rail attached
0 2023/12/06 22:59:57
Here is what I meant. Cut the wires then turn the red tab connector facing down, then connect the wires straight across. Purple to brown, yellow to white, white to yellow, brown to purple.
Here is what I meant. Cut the wires then turn the red tab connector facing down, then connect the wires straight across. Purple to brown, yellow to white, white to yellow, brown to purple.
0 2023/12/06 22:59:51
I also tack welded a flat washer into the recessed around of the bolt hole. The washer is slightly higher that the surface of the bracket, for ease of bolting the flat bracket on.
I also tack welded a flat washer into the recessed around of the bolt hole. The washer is slightly higher that the surface of the bracket, for ease of bolting the flat bracket on.
0 2023/12/06 22:38:15
Mocked up. Notice the notch to clear camshaft sensor.
Mocked up. Notice the notch to clear camshaft sensor.
0 2023/12/06 22:38:09
Fresh paint. I used rustoleum appliance enamel that I had at the moment.
Fresh paint. I used rustoleum appliance enamel that I had at the moment.
0 2023/12/06 22:38:05
How it would be mounted to the engine block.
How it would be mounted to the engine block.
0 2023/12/06 22:37:58
0 2023/12/06 22:37:51
0 2023/12/06 22:25:53
0 2023/12/06 22:25:48
0 2023/12/06 22:25:42