Jeep Cherokee Forum
I ground down the edges to be welded, and attached a cap on the angles end. Welds aint the best but they will clean up later.
I ground down the edges to be welded, and attached a cap on the angles end. Welds aint the best but they will clean up later.
0 2024/04/24 19:12:03
Made to fit.
Made to fit.
0 2024/04/24 19:11:56
You can see here I copied the contors of the interal angles.
You can see here I copied the contors of the interal angles.
0 2024/04/24 19:11:50
Marked for cuts. I'll verify the measurements later after I 100% finalize the design, and post them.
Marked for cuts. I'll verify the measurements later after I 100% finalize the design, and post them.
0 2024/04/24 19:11:44
All the accessories are off.
All the accessories are off.
0 2024/04/24 19:11:37
I drilled out all of the spot welds. I tried to perfect the technique of not drilling it on like 4 other can but unfortunately could not make it work.
I drilled out all of the spot welds. I tried to perfect the technique of not drilling it on like 4 other can but unfortunately could not make it work.
0 2024/04/24 19:11:30
Its life started as a 40mm can
Its life started as a 40mm can
0 2024/04/24 19:11:22
0 2024/03/02 14:32:32
0 2023/11/17 12:37:16
0 2023/11/10 14:45:09
0 2023/11/10 14:45:02
Finished product!
Finished product!
0 2023/11/10 14:44:55
Ran it through like normal and bolted it all together
Ran it through like normal and bolted it all together
0 2023/11/10 14:44:49
Better photo of how jacked up it turned out
Better photo of how jacked up it turned out
0 2023/11/10 14:44:42
0 2023/11/10 14:44:36
The hole isnt centered and I didn't have a 14mm drill bit so it's a little wierd
The hole isnt centered and I didn't have a 14mm drill bit so it's a little wierd
0 2023/11/10 14:44:30
I took the platic XJ adapter and made a CAD (cardboard aided design) and make a metal bracket and new seal
I took the platic XJ adapter and made a CAD (cardboard aided design) and make a metal bracket and new seal
0 2023/11/10 14:44:21
The cover took a little massaging but I got it in place. The foot pedal scatched the fresh paint a little, but at this point in the mod, im okay with it. Maybe I'll respray it when I get stiffer springs in the assembly.
The cover took a little massaging but I got it in place. The foot pedal scatched the fresh paint a little, but at this point in the mod, im okay with it. Maybe I'll respray it when I get stiffer springs in the assembly.
0 2023/10/14 12:01:33
Got it installed! I was able to run the bolts from outside the fender into the welded nuts. You can see here i also did some wire management.
Got it installed! I was able to run the bolts from outside the fender into the welded nuts. You can see here i also did some wire management.
0 2023/10/14 12:01:25
Something I found out while trying to install whas the MJ switch wouldnt fit into the the XJ connector. I tried using the XJ switch but it routed the wire straight into the assembly and pinched the wire. There was this lip thats punched out to retain the MJ connector and i pressed it back into place and it fit no problems. The XJ one has a hole drilled in it for the connector to fall into. Oh well, it works.
Something I found out while trying to install whas the MJ switch wouldnt fit into the the XJ connector. I tried using the XJ switch but it routed the wire straight into the assembly and pinched the wire. There was this lip thats punched out to retain the MJ connector and i pressed it back into place and it fit no problems. The XJ one has a hole drilled in it for the connector to fall into. Oh well, it works.
0 2023/10/14 11:58:29
0 2023/08/26 09:48:02
This is about where the rear connector wil lay in relevance to the parking brake assembly. I wont know for sure where exactly to posistion this end until I get the parking brake finished and connected to the other end of the cable.
This is about where the rear connector wil lay in relevance to the parking brake assembly. I wont know for sure where exactly to posistion this end until I get the parking brake finished and connected to the other end of the cable.
0 2023/08/26 09:47:55
Got it slid back into place
Got it slid back into place
0 2023/08/26 09:47:47
0 2023/08/26 09:47:19
Jd
Jd
0 2023/08/20 11:41:19
Jd
Jd
0 2023/08/20 11:41:12
Jd
Jd
0 2023/08/20 11:41:06
Jd
Jd
0 2023/08/20 11:40:59
Jd
Jd
0 2023/08/20 11:40:52
Jd
Jd
0 2023/08/20 11:40:44
Hd
Hd
0 2023/08/20 11:40:37
0 2023/08/19 11:43:10
0 2023/08/13 08:01:06
0 2023/08/12 20:51:32
0 2023/08/12 20:51:25
And the plastic trim panel fits back into place. Just need to buy new bolts to fit the new threads.
And the plastic trim panel fits back into place. Just need to buy new bolts to fit the new threads.
0 2023/08/12 20:51:16
0 2023/08/12 20:51:08
0 2023/08/12 20:50:29
Broke the head right off. This is what I was left
Broke the head right off. This is what I was left
0 2023/08/12 20:47:48
Peep the 242JHD swap
Peep the 242JHD swap
0 2023/08/12 20:47:37