Jeep Cherokee Forum
Very bright - I was seeing spots for a while after this picture
Very bright - I was seeing spots for a while after this picture
0 2016/02/03 15:33:55
Plug-and-play
Plug-and-play
0 2016/02/03 15:33:50
3 LED system the top 2 are for low beam and all 3 are for high beam
3 LED system the top 2 are for low beam and all 3 are for high beam
0 2016/02/03 15:33:43
Pretty slick setup
Pretty slick setup
0 2016/02/03 15:33:38
30w H4 LED Headlight bulbs
30w H4 LED Headlight bulbs
0 2016/02/03 15:33:13
Cree LED H4 Headlight Lighting system
Cree LED H4 Headlight Lighting system
0 2016/02/03 15:33:05
Jack handle isolator
Jack handle isolator
0 2016/02/03 15:27:48
4XRAC Jack Mounting System to attach to the side of my roof rack
4XRAC Jack Mounting System to attach to the side of my roof rack
0 2016/02/03 15:27:37
60" model - black & red for obvious reasons
60" model - black & red for obvious reasons
0 2016/02/03 15:26:34
hi lift jack was delivered today
hi lift jack was delivered today
0 2016/02/03 15:26:26
0 2016/02/03 14:17:49
0 2016/02/02 15:07:17
0 2016/02/02 15:07:13
0 2016/02/02 15:07:08
0 2016/02/02 15:07:04
0 2016/02/02 15:07:00
0 2016/02/02 15:06:55
0 2016/02/02 15:06:50
0 2016/02/02 15:06:42
0 2016/02/01 15:25:23
0 2016/02/01 15:25:17
0 2016/02/01 15:25:12
0 2016/02/01 15:25:08
0 2016/02/01 15:25:01
0 2016/02/01 15:24:54
0 2016/01/30 08:50:10
0 2016/01/30 08:50:05
0 2016/01/30 08:49:54
Laid out the fans and marked all the mounting locations using a center punch.
Laid out the fans and marked all the mounting locations using a center punch.
0 2016/01/30 08:49:07
Got the fans laid out and marked all the mounting holes using a center punch. Drilled all the holes twice, once using a 1/8" bit and finally using a 1/4" bit.
Got the fans laid out and marked all the mounting holes using a center punch. Drilled all the holes twice, once using a 1/8" bit and finally using a 1/4" bit.
0 2016/01/30 08:47:37
Mounting up my cooling fans to my aluminum fan shroud.
Mounting up my cooling fans to my aluminum fan shroud.
0 2016/01/30 08:46:38
0 2016/01/30 08:37:54
Engine side view.
Engine side view.
0 2016/01/30 08:37:46
All mounted up. Here's a radiator side view.
All mounted up. Here's a radiator side view.
0 2016/01/30 08:37:39
Everything laid out. I started out with center punching the mounting locations, then used a 1/8" drill bit to pre-drill the holes and finally used a 1/4" bit to drill the final hole. Mounted the fans using 1/4" bolts, lock washers & nuts.
Everything laid out. I started out with center punching the mounting locations, then used a 1/8" drill bit to pre-drill the holes and finally used a 1/4" bit to drill the final hole. Mounted the fans using 1/4" bolts, lock washers & nuts.
0 2016/01/30 08:37:33
Finally got around to mounting my cooling fans to my aluminum fan shroud.
Finally got around to mounting my cooling fans to my aluminum fan shroud.
0 2016/01/30 08:37:24
Also it melted the rear dome light connector at the light. If anyone out there knows where i could get one or someone has an extra one i would greatly appreciate it. I know I could go to the JY and find one, but I'm lazy and it's cold out.
Also it melted the rear dome light connector at the light. If anyone out there knows where i could get one or someone has an extra one i would greatly appreciate it. I know I could go to the JY and find one, but I'm lazy and it's cold out.
0 2016/01/24 15:40:27
It looks like the wiring got wet and corroded, causing the wires to short against each other. It melted the connectors also.
It looks like the wiring got wet and corroded, causing the wires to short against each other. It melted the connectors also.
0 2016/01/24 15:40:20
I traced it to the passenger rear side compartment rear dome light speaker connector
I traced it to the passenger rear side compartment rear dome light speaker connector
0 2016/01/24 15:40:10
All done - I am going to wait to reinstall this until Spring since I am going to add some sound deadening material to the ceiling.
All done - I am going to wait to reinstall this until Spring since I am going to add some sound deadening material to the ceiling.
0 2016/01/19 16:46:03