Jeep Cherokee Forum
0 2020/07/17 18:47:13
0 2020/07/17 18:49:21
I have some 1.25" heims and bungs to fit 2" tube enroute. Ws planning to get castor locked down with short arms kind get the bugs worked out then go lng arm. It may not happen that wy with so much cstor to kill Just thught id share in this thread since this is actually happening raised arms at axle end. Ohhh im also going to run the upper off the passenger side and raise it to. Helk if i can get castor sorted out with these short arms il run the 3link like i said for awhile.
I have some 1.25" heims and bungs to fit 2" tube enroute. Ws planning to get castor locked down with short arms kind get the bugs worked out then go lng arm. It may not happen that wy with so much cstor to kill Just thught id share in this thread since this is actually happening raised arms at axle end. Ohhh im also going to run the upper off the passenger side and raise it to. Helk if i can get castor sorted out with these short arms il run the 3link like i said for awhile.
0 2020/07/17 18:56:14
Im stoked
Im stoked
0 2020/07/18 00:44:26
0 2020/07/18 08:11:19
0 2020/07/18 08:12:02
Im currently working on putting my raised short arms raised the xle end im going to run this 3 linked with a johny joint pressed in. Then drift into a longer armed similar to the sfr.
Im currently working on putting my raised short arms raised the xle end im going to run this 3 linked with a johny joint pressed in. Then drift into a longer armed similar to the sfr.
0 2020/07/19 09:31:56
0 2020/07/19 16:17:25
0 2020/07/19 16:22:10
0 2020/07/19 16:23:53
0 2020/07/21 21:29:51
0 2020/07/21 21:30:18
I did cheap out and will be running bushings on the axle end partly because the 1.25 heim wont clear in my raised bracket. Had to share
I did cheap out and will be running bushings on the axle end partly because the 1.25 heim wont clear in my raised bracket. Had to share
0 2020/07/21 21:30:56
Its in. Raising lowers arms did make it dive. Ill be raising upper with couple options to tune. Seperation at 7 and 8" It is much smoother and softer feeling off road.
Its in. Raising lowers arms did make it dive. Ill be raising upper with couple options to tune. Seperation at 7 and 8" It is much smoother and softer feeling off road.
0 2020/07/23 20:55:32
0 2020/07/23 21:00:30
0 2020/07/26 19:46:53
0 2020/07/26 22:54:01
0 2020/07/27 00:06:19
0 2020/07/27 00:06:50
Upper link mock up. Ughhh
Upper link mock up. Ughhh
0 2020/07/28 09:22:19
0 2020/07/28 23:08:27
0 2020/07/29 16:46:20
0 2020/07/29 16:57:24
0 2020/07/29 21:11:09
At this rate ill be done sometime next year
At this rate ill be done sometime next year
0 2020/07/29 21:12:33
I have considered recentering some h1 wheels nd running skid steer tires similar to these. I have a tire knive and could really have some fun with them.
I have considered recentering some h1 wheels nd running skid steer tires similar to these. I have a tire knive and could really have some fun with them.
0 2020/08/01 11:59:58
0 2020/08/03 11:53:27
0 2020/08/05 08:30:43
0 2020/08/06 00:17:05
0 2020/08/06 00:17:40
0 2020/08/06 00:18:23
0 2020/08/06 00:19:01
Hoping ounce i finish removing factory lower mount it gains just enough clearance
Hoping ounce i finish removing factory lower mount it gains just enough clearance
0 2020/08/06 00:19:47
Shocks balot on over top of bar bolt. Kinda a pain havong them live in the same place. Though its working well
Shocks balot on over top of bar bolt. Kinda a pain havong them live in the same place. Though its working well
0 2020/08/06 00:25:23
Lower position on axle
Lower position on axle
0 2020/08/07 11:33:14
0 2020/08/07 11:35:36
0 2020/08/08 15:39:47
0 2020/08/08 15:41:26
0 2020/08/08 15:42:50
2x3x.25 cross member, its bolted in incase tranny needd removed.
2x3x.25 cross member, its bolted in incase tranny needd removed.
0 2020/08/08 15:43:48