Jeep Cherokee Forum
0 2020/05/27 12:35:14
0 2020/05/27 12:36:28
0 2020/05/27 12:38:40
0 2020/06/02 12:06:52
0 2020/06/02 12:07:32
0 2020/06/02 12:08:35
0 2020/06/08 20:24:21
33x12.5 when my rig had closer to 3" I cut alot to fit them. On the
33x12.5 when my rig had closer to 3" I cut alot to fit them. On the
0 2020/06/08 20:42:26
0 2020/06/08 22:06:53
Shocks might munt off the side of lower control arms
Shocks might munt off the side of lower control arms
0 2020/06/08 22:07:37
0 2020/06/08 22:10:25
0 2020/06/08 22:12:25
0 2020/06/11 06:45:04
0 2020/06/11 06:45:48
0 2020/06/11 06:46:21
0 2020/06/11 09:59:07
Few more feet to get to the header then the hard parts out of the way. Ive done a few jeep exhaust but this will be the first going all the way. Pipe is 2.5" hoping to put muffler where its pictured. Just roughing in bends so i hve something to work with ounce im laying under the jeep. More to come.
Few more feet to get to the header then the hard parts out of the way. Ive done a few jeep exhaust but this will be the first going all the way. Pipe is 2.5" hoping to put muffler where its pictured. Just roughing in bends so i hve something to work with ounce im laying under the jeep. More to come.
0 2020/06/12 17:58:04
0 2020/06/14 22:00:00
Well its to loud. Might put a flopro twister on it. I haven't told the owner yet. It does run better but is to loud.
Well its to loud. Might put a flopro twister on it. I haven't told the owner yet. It does run better but is to loud.
0 2020/06/14 22:00:41
0 2020/06/15 20:05:39
0 2020/06/15 20:08:36
0 2020/06/18 18:03:05
0 2020/06/19 16:31:28
This is pretty close to it should be. This is my jeep my track bar maches drag link for angle and almost length. Only difference is your drag link munts under the knucke and you have stock track munt on the axle side. Jack the jeep up tires 4" off the ground stick a long digger bar under tire and pry up. Your looking for slop in balljoints and control arm bushing that may cause wobble. Dont discount parts that are new or thught to be new.
This is pretty close to it should be. This is my jeep my track bar maches drag link for angle and almost length. Only difference is your drag link munts under the knucke and you have stock track munt on the axle side. Jack the jeep up tires 4" off the ground stick a long digger bar under tire and pry up. Your looking for slop in balljoints and control arm bushing that may cause wobble. Dont discount parts that are new or thught to be new.
0 2020/06/19 16:47:51
0 2020/06/19 17:20:39
0 2020/06/19 17:26:58
0 2020/06/24 21:31:42
0 2020/06/24 21:32:28
Even cleaned under the hood. Need to make something to support coolant hoses some day
Even cleaned under the hood. Need to make something to support coolant hoses some day
0 2020/06/24 21:33:32
Then sunset into a thunder storm.
Then sunset into a thunder storm.
0 2020/06/24 21:35:03
My 3" turn down at axle
My 3" turn down at axle
0 2020/06/25 07:18:01
I guesd i didn't put a photo of the finished 30 up yet.
I guesd i didn't put a photo of the finished 30 up yet.
0 2020/06/26 17:26:35
0 2020/06/28 09:23:51
0 2020/06/28 11:17:10
0 2020/06/28 11:18:00
Taking it slow and easy
Taking it slow and easy
0 2020/06/28 11:18:53
0 2020/07/01 21:21:40
0 2020/07/15 23:11:47
0 2020/07/15 23:12:23
Shes lipless
Shes lipless
0 2020/07/15 23:13:49